TYPICAL CONNECTIONS
DEEP SEA ELECTRONICS
ISSUE 3
053-021
4120 INSTALLATION INSTRUCTIONS
With the unit in Stop mode, Configuration Mode is selected by operation of a small
switch on the rear, bottom edge of the PCB. This is partially hidden to prevent
accidental operation
Once Configuration Mode is selected, the Auto LED will commence rapid flashing.
When in Configuration Mode all normal operation is suspended.
The Stop pushbutton can be used to select the LED code that corresponds to the
required function. The 5 left hand LEDs will form the code.
The Manual pushbutton will allow the user to change the function parameters. The 3
right-hand LEDs inform the user of the current setting for the chosen function.
When the required parameters are displayed, pressing the Auto button will save the
new setting. The process is repeated for each function change.
When configuration is complete, the Configuration Mode Selector Switch should be
returned to the Normal position. A key to all configuration options is provided
overleaf on the Functions and Parameters table.
Exercise scheduler - Press and hold the Auto button for 6 seconds. The generator
will run for 30 minutes, this will be repeated automatically every 7 days from the time
the scheduler was set. When the timer is active the led above the Auto button will
flash. To disable the scheduler press and hold the Auto button again for 6 seconds,
the led above the Auto button will stop flashing.
Panel Cut Out :
154mm x 98mm (6.1 x 3.9)
Normal mode
Configure mode
Deep Sea Electronics Plc.
Deep Sea Electronics inc.
Highfield House, Hunmanby Industrial Estate, North Yorkshire.
YO14 0PH.
ENGLAND
Tel:+44 (0)1723 890099.
Fax: +44 (0)1723 893303.
LO CALL (from UK BT landlines) :
Telephone 0845 260 8900. Fax 0845 260 8901
Email: sales@[Link]
Web: [Link]
3230 Williams Avenue
Rockford, Illinois 61101-2668, U.S.A.
Phone: +1 (815) 316-8706. Fax: +1 (815) 316- 8708
TOLL FREE (USA only) : Tel: 1 866 636 9703 Email:
dsesales@[Link]
Web: [Link]
Technical Support (Indonesia) : +6281 288 488 513
FUNCTIONS AND CONFIGURATION TABLE
Function
Pre-heat Timer
Start Delay
Stop Delay
Energise to Stop Timer
Warm-up Timer
Cooling Timer
Nominal Frequency
Nominal DC Voltage
LOP Switch Contact
HET Switch Contact
Crank disconnect on Oil
Pressure
Underspeed detection
Remote start function
Remote start on load
(ignore if simulated mains)
Auxiliary Input 1 Function
Auxiliary Input 2 Function
Auxiliary Output 1 Function
Auxiliary Output 2 Function
Mains Under Voltage
{
{
{
{
z
z
z
z
{
{
{
{
z
z
z
z
{
{
{
{
z
z
z
z
{
{
{
{
z
z
z
z
{
{
{
{
z
z
z
z
{
{
{
{
z
z
z
z
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
z
z
z
z
{
{
{
{
z
z
z
z
{
{
{
{
z
z
z
z
{
{
{
{
z
z
z
z
{
{
{
{
z
z
z
z
! 1
{
{
z
z
{
{
z
z
{
{
z
z
{
{
z
z
{
{
z
z
{
{
z
z
{
{
z
z
{
{
z
z
{
{
z
z
{
{
z
z
{
{
z
z
{
{
z
z
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
{
z
z
{
{
z
z
{
{
z
z
{
{
z
z
{
{
z
z
{
{
z
z
{
{
z
z
{
{
z
z
{
{
z
z
{
{
z
z
! 2
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
{
z
Value (Default in bold Italics)
0 Seconds
5 Seconds
10 Seconds
15 Seconds
20 Seconds
30 Seconds
60 Seconds
180 Seconds
0 Seconds
5 Seconds
10 Seconds
15 Seconds
20 Seconds
30 Seconds
60 Seconds
180 Seconds
0 Seconds
5 Seconds
10 Seconds
15 Seconds
20 Seconds
30 Seconds
60 Seconds
180 Seconds
0 Seconds
5 Seconds
10 Seconds
15 Seconds
20 Seconds
30 Seconds
60 Seconds
180 Seconds
0 Seconds
5 Seconds
10 Seconds
15 Seconds
20 Seconds
30 Seconds
60 Seconds
180 Seconds
0 Seconds
5 Seconds
10 Seconds
15 Seconds
20 Seconds
30 Seconds
60 Seconds
180 Seconds
50 Hz (O/S +14% / Overshoot
60 Hz (O/S +14% / Overshoot +24%)
12V DC (CF 8V)
24V DC (CF 16V)
Close on Fault
Open on Fault
Close on Fault
Open on Fault
Disabled
Enabled (2 Second Delay)
Disabled
Enabled (U/S 20%)
Remote start
Simulated mains
Remote start is off load
Remote start is on load
Immediate Warning Close on Fault
Immediate Warning Open on Fault
Immediate Shutdown Close on Fault
Immediate Shutdown Open on Fault
Delayed Warning Close on Fault
Delayed Warning Open on Fault
Delayed Shutdown Close on Fault
Delayed Shutdown Open on Fault
Immediate Warning Close on Fault
Immediate Warning Open on Fault
Immediate Shutdown Close on Fault
Immediate Shutdown Open on Fault
Delayed Warning Close on Fault
Delayed Warning Open on Fault
Delayed Shutdown Close on Fault
Delayed Shutdown Open on Fault
Not used
Pre-heat
Load transfer
Common Warning
Common Shutdown
System in Auto
Common Alarm
Energise to Stop
Not used
Pre-heat
Load transfer
Common Warning
Common Shutdown
System in Auto
Common Alarm
Energise to Stop
60V / 70V
70V / 80V
80V / 90V
90V / 100V
120V / 140V
140V / 160V
160V / 180V
180V /200V
