ASSOCIATION OF STRUCTURAL ENGINEERS, OF THE PHILIPPINES, INC. NATIONAL STRUCTURAL CODE OF THE mam ede te) is Piel Eis iat Fars His VOLUME | BUILDINGS, TOWERS, AND OTHER VERTICAL STRUCTURESa NATIONAL STRUCTURAL CODE OF THE PHILIPPINES 2015 VOLUME I BUILDINGS, TOWERS AND OTHER VERTICAL STRUCTURES SEVENTH EDITION First Printing, 2016 Association of Structural Engineers of the Philippines, Inc. Suite 713, Future Point Plaza Condominium 1 112 Panay Avenue, Quezon City, Philippines 1100 + (632) 410-0483, (£632) 411-8606 [email protected] + http://www.aseponline.org National Structural Code of the Philippines Volume |, 7th Edition, 1* Printing, 2076 fiPREFACE TO THE NSCP VOLUME 1, SEVENTH EDITION, 2015 Introduction [ASEP recognizes the need for an up-to-date structural code addressing the design and installation of structural systems through requirements emphasizing performance. The new National Structural Code of the Philippines (NSCP Volume lis designed to meet these needs through various model codes/regulations, generally from the United States, to safeguard the pablic health and safety nationwide. ‘Thi’ updated Structural Code establishes minimum requirements for structural systems using prescriptive and performance-based provisions. I is founded on broad-based principles that make possible the use of new materials and Pow building designs. Also, this code reflects the latest seismic design practice for earthquake-resistant structures Changes and Developments In its drive to upgrade and update the NSCP, the ASEP Codes and Standards Committe initially wanted to adopt the latest ditions of American code counterparts. However, for eases where available local data i limited to support the upgrade, then some provisions and procedures of the NSCP 7" edition were retained, ‘This NSCP 7th eition is referenced from the following: 2. Uniform Building Code UBC-1997 b. International Building Code 1BC-2009 c. American Society of Civil Engineers ASCE/SE! 7-10 4. American Concrete Institute ACI318-14M e __American Institue for Steel Constuction AISC-0S with Supplementary Seismic Provisions £ American Tron and Stee! Institute AISI $100-2007 & Reinforced Masonry Engineering Handbook of America h. Concrete Masonry Handbook, th Edition i. American National Standard Institute ANSI EIA'TIA-222-G-1-2007 |. American Society for Testing and Materials (ASTM) Standards Significant revisions ae summarized as follows: & ——Chapier 1~ General Requirements “The changes made inthis chaptor are the following 1 Section 102 Definition of Failure a2 Section 103 ~ Classification of Structures School buildings of more than one story, hospitals, designated evacuation centers, structures are under the essential facilities category. Section 104 ~ Design Requirements Churches, Mosque and other related religious structures are under the special occupancy category Section 104-Design Requirements. “The provision for deftection of any structural member under the serviceability requirement is deleted, This cequirement for concrete and steel is specified in Chapters 4 and 5 respectively. [New requirements are added tothe design review seetion. a3 Section 105 ~ Posting and Instrumentation ‘Association of Structural Engineers of the Philippines, Inc. (ASEP) vaa ‘The provision of installed recording accelerograph is adjusted. Inclusion of Appendix I-A : Recommended Guidelines on Structural Design Peer Review of ‘Structures 2015 Inclusion of Appendix 1-B: Guidelines and Implementing Rules on Earthquake Recording Instrumentation for Buildings (Chapter 2 ~ Minimum Design Loads The changes made in this chapter are the following: ba b2 b3 ba Section 203 ~ Combination of Loads ‘The load factors and load combinations are revised particularly the load combinations including wind load Section 205 ~ Live Loads Additional loads are incorporated in the table for minimum uniform and concentrated loads particulary the parking garage and ramp live load. Section 207 ~ Wind Loads Wind load provisions, which were previously based on ASCET-05, are updated based on ASCET-10, In this edition, three different wind contour maps for the entire Philippine archipelago are generated and provided for determining the basic wind speeds for different categories of building occupancies as defined in Table 103-1, These maps provide basic wind speeds that are directly applicable for determining pressures for design strength, Strength design wind load factor ig 1.0; whereas, allowable stress design wind load factor is 0.6, Generally, basic wind speeds correspond to 3%, 7% and 1$% probability of exceedance in SO years (MRI = 1700,700 and 300 years, respectively). Four (4) permitted procedures in ‘determining the design wind loads for main wind-force resisting eystems (MWFRS), for other structares and building appurtenances and for components and cladding (C&C) are provided such as: ‘© directional procedure for buildings of all heights, © envelope procedure for low-rise buildings, ‘* directional procedure for other structures and building appurtenances and analytical procedure for components & cladding, and ‘© wind tunnel procedure ‘The ANSI EIA/TIA-222-G-2005 and ANSI ELA/TIA-222G-1-2007 are now fully referenced for computing wind loads on stee! antenna towers and antenna supporting steuetures. Section 208 Earthquake Loads ‘The near-soutce factors for 2-km distance from a causative fault is included in addition to 5- km, 10-km, 15-km distance and beyond 15-km distance. ASCEISEI 7-10, using spectral acceleration, is recognized as an alternative procedure in the determination ofthe earthquake loads ‘Chapter 3- Earthworks and Foundations ‘The revisions made in this chapter are the following: Provisions pertaining to the conduet and interpretation of foundation investigations for cases involving liquefiable, expansive or questionable sols are adopted National Structural Code of the Philippines Volume |, 7th Edition, 1” Printing, 2076c2_ The section on footings is amended to incomorate provisions for differential settlement, design loads and vibratory loads; ¢3 The section on pile foundations is amended to incorporate new provisions on splicing of ‘concrete piles and cd Thesection on special foundations, slope stabilization and materials of eonstrution are added. 5 Provisions for construction in Zone 4 pertaining to reinforcement of Precast Prestressed Piles have boon revised to ensure consistency with ACI 318, 66 The figure for cut slopes has been amended for clarity; 67 The figore for fill slopes has been amended for clarity and some provisions have been modified: 8 A table on the minimum required number of boreholes has been added to the section om foundation investigation: 69 Provisions pertaining to minimum dimensions of ditches have been modified 610 The section on excavations and fills has been amended to incorporate provisions for scouring and erosion proteetion as well as support of excavations and open cuts: cll Provision pertaining to general pile requirements have been expand to include design of piles and pile groups subjected to lateral loads. 12 A Section on MSE Struetures and ilar Reinforced Embankments and Fills has been added. Chapter 4 - Structural Concrete ‘To reflect the reorganization of ACI 318-14 which contained 2 number of significant technical changes, the ASEP adopted similar changes in the NSCP 2015 7th Edition. The latest ACI 318 was reorganized as « member- based document, i, e., particular member type, such as beam, column, or slab will have separate sub-sections for all requirements to design that particular member type. ‘This will eliminate the need to flip through several Sections to comply with all the necessary design requirements for a particular structural member, 9s was necessary withthe old organization format, 41 Section 401: General General information regarding the scope and applicability of NSCP 2015, Vol. 1 is provided. Additional sub- seetion on interpretation is included to help users better understand Chapter 4, Structural Concrete, 42 Seotion 402: Notation and Terminology ‘The definition for hoops has been modified because the use of interlocking headed bars is a concem regarding the possibility that it will not be adequately interlocked and because the heads could become disengaged under complex loadings well into the non-linear range of response. It is now defined as a closed tie or continously :vound tie, made up of one or several reinforcement elements, each having seismic hooks at both ends. [A definition for special seismic systems, a term used in Sections 418 and 419, has been added 43 Section 403: Referenced Standards “The following referenced specifications have been added to Section 403.2.4 ‘» ASTM A370-14, Standard Test Methods and Definitions for Mechanical Testing of Steel Producis ‘ASTM A1085-13, Standard Specification for Cold-Formed Welded Carban Stee! Hollow Structural Sections (HSS) «ASTM C173/C173M-14, Standard Test Method for Air- Content of Freshly Mixed Conerete by Volumetric Method ‘Association of Structural Engineers ofthe Philippines, Inc. (ASEP) 1 ii ‘+ ASTM C1582/C1582M-11, Standard Specification for Admistures to Inhibit Chloride Induced Corrosion of Reinforcing Steel in Concrete ‘A now referenced specification from Australia and New Zealand, Section 403.2.6 is added. These standards were included as ACI 318 has no provisions related to Qualifications on the Use of Quenctied ‘Tempered QT/Thermo-Mechanically Treated Reinforcement, which are the type manufactured, sold, ‘and commonly used for building construction inthe Philippines ‘AS/NZS 4671: 2001, Steel Reinforcing Materials ‘+ NZS 3101: 2006, Part 1 and Part 2, Concrete Structures Standaed, and Design of Concrete Structures # NZS 3109, Amendment 2, Welding of Reinforcing Steel * ASINZS 1554.3: 2008, Part 3, Structural Steel Welding of Reinforcing Steel ‘The following referenced specifications have been deleted + ASTM C109/C109M-08, Standard Test Method for Compressive Strength of Hydraulic ‘Cement Mortars (Using 50 mm Cube Specimens) * ASTM C192/C192M-07, Standard Practice for Making and Curing Conerete Test Specimens in the Laboratory Several referenced standards and specifications have been updated, as in most eases with every edition of the NSCP. Note that the edition of every referenced standard is important. The NSCP does not necessarily adopt new editions of referenced standards unless they are vetted before the publication of each edition ofthe standard, 4 ds Section 404: Structural System Requirements ‘This new Section has been added 10 Chapter 4 to introduce structural system requirements, ‘This Section contains Sub-scctions on Materials, Design Loads, Structural System and Load Paths, Structural Analysis, Strength, Serviceability, Durability, Sustainability, Structural Integrity, Fire Resistance, Requirements for Specitie Types of Construction, Construction and Inspection, and Strength Evaluation of Existing Structures, Most of these Sub-sections refer to the other Sections in the NSCP. The Sub-section on construction and inspection, for instance, refers to Section 426, In the areas for Sustainability and Fire Resistance, the NSCP does not have specifie requirements. This Sub-section on Sustainability allows the licensed design professional to specify in the construction documents, sustainability requirements in addition to the strength, serviceability, and durability requirements of the NSCP, The strength serviceability. and durability requirements are required to take precedence over sustainability Considerations, though these requirements are generally in harmony with sustainable siructures. In the Sub-section on Fire Resistance, the NSCP refers to the fire-protection requirements of the NSCP Chapter 4, Sub-sestion 420.6.1. However, ifthe National Building Code of the Philippines requires a greater concrete cover, such greater thickness shall govern. Seetion 405: Loads The following modification has been made in the provision for live load reduction because ‘there are still unincozporated arcas where there may not be included in the previous editions of the NSCP. The 7° Edition, Sub-section 405.2.3 — Live load reductions shall be permitted in accordance with the National Building Code of the Philippines, or in its absence, in accordance with ASCE/SEI 7, For many Code revision cycles, ACI 318 retained provisions for service-level earthquake forces in the design load combinations, In 1993, ASCEISEI 7 converted earthquake forces to strength-level forces and reduced the earthquake load factor to 1.0, and the model building National Structurel Code of the Philippines Volume I, 7th Edition, 1 Printing, 2016codes followed suit, In modern building codes around the world, earthquake fonds are now stengti-level forees. Any references 10 service-level earthquake forces have been deleted 446. Section 406: Structural Analysis ‘The following new itern has been added in Sub-section 406 6.2.3 (b) For frames or continuous construction, it shall be permitted to assume the intersecting member regions are rigié. Previous NSCP 6" Ealition has been silent on the use of finite element analysis (FEA), though itis now frequently used. Sub-seetion 406.9 now has provisions that are intended to explicitly allow the use of FEA and to provide a framework for the future expansion of FEA provisions, but not as gui toward the selection and use of FEA software, The new Sub-section on diaphragms and collectors makes explicit reference to the use of FEA, which makes it imperative that the NSCP 7* Edition recognize the acceptability ofits use. 4.7 Section 408: Two-Way Slabs ‘Sub-seetion 418.10.1 (corresponding to ACI 318M-L, Section 18.9.1), says thet a minimum area of bonded reinforcement shall be provided in all flexural members with unbonded prestressing tendons, The purpose of the minimam unbonded reinforcement over the tops of ‘columns js to distribute cracking enused by high local flexural tensile stresses in areas of peak negative moments, However, the high local flexural tensile stresses are not unique to slabs ‘with unbonded tendons. The new reorganized Sub-section 408.6.2.3 (corresponding to ACL 318M-14 Section 8.6.2.3) requires the same minimum reinforcement in slabs with unbonded ‘or bonded tendons, except that the aren of bonded tendons is considered effective in controlling cracking. Ik was also decided by the ACI 318 Committee, that if the same bonded reinforcement were required for both bonded and unbonded post-tensioned two-way systems, the structural integrity requirements for both systems should also be the same, The structral integrity requirements. in ACT 318M-I1, Section 18.12.6 applied to two-way post-ensioned slab systems with unbonded tendons only. The structaral integrity requirements in ACL 318M-14 Section 8.7.5.6 (corresponding to the NSCP 2015, Sub-section 408.7.5.6) now apply to two- \way posttensioned slab systems with bonded as well as unbonded tendons. 48 Section 409: Beams ‘The use of open web reinforcement for torsion and shear in slender spandrel beams by the precast concrete industry 8 an alternative to the closed stirups traditionally mandated by this ‘Code. Eliminating closed stirrups is desirable because they cause reinforcement congestion: production costs also increase significantly because pre-tensioning strand must be thrended through the closed stirrups. ‘A new relevant Sub-seetion 409.5.4.7 for solid precast sections is added to the NSCP 7" Edition 49 Section 412: japhragms For the first ime, a new Section 412, added design provisions for diaphragms in buildings constructed in areas of low seismicity (Zone 2) The new Section applies “to the design of non- prestressed ond prestressed diaphragms, including: (2). Diaphragms tha are cast -place slabs (6). Diaphragms that comprise a cast-in-place topping slab on precast elements ‘Association of Structural Engingers of the Philippines, Inc. (ASEP) vili | i aio aan az (©). Diaphragms that comprise precast elements with end strips formed by either a cast- in-place concrete topping slab or edge beams (@). Diaphragms of interconnected precast clements without cast-in-place concrete topping Section 418: Barthquake-Resistant Structures ‘There are a number of significant and substantive changes to this Section Column confinement - The ability ofthe concrete core of a concrete reinforeed column to sustain compressive strains tends to increase with confinement pressure, Confinement requirements for columns of special moment frames, and for columns not designated as part of the seismic-force-esisting system in structures assigned to seismic zone 4 (similar to ASCE 7-10 Seismic Design Categories D, E, end F), with high exial load or high concrete compressive strength are significantly diferent. ‘Transverse reinforcement - One important new requirement for special moment frame columns are included in Sub-sections 418.7.5.2 and 418.1.5.4. There are new restrictions on the use of headed reinforcement to make up hoops. Special moment frame beatn-column joints ~ For beam-coluran joints of special moment frames, clarification of | the development fength of the beam longitudinal reinforcement that is hooked, requirements for joints with hheaded longitudinal reinforcement, and restrictions on joint aspect ratio are new, For beam-columin joints of special moment frames, clarification of development length of beam longitudinal reinforcement that is hooked, requirements for joints with headed longitudinal reinforcement, and restrictions on joint aspect rato are new. Special shear walls ~ Subsection 418.10 (equivalent to ACI 318-14M-14 Section 18.10, previously ACI 318M-I1 Section 21.9), has been extensively revised in view of the performance of buildings in the Chile earthquake of 2010 and the Christchurch, New Zealand, earthquakes of 2011, as wells as fullescale reinforced concrete building tests, In these earthquakes and laboratory tests, concrete spalling and vertical reinforcement buckling were at times observed at wall boundaries, For ASTM AGI5 Grade 420 bars used as longitudinal reinforcement in special moment frames and special shear ‘walls the NSCP 7" Edition now requires the same minimum elongation as ASTM A706 reinforcement, Section 419: Concrete: Design and Durability Requiremen Quite 2 few changes have been made in concrete durability eequirements, which are now located in this Section, Section 420: Steel Reinforcement Properties, Durability and Embedments ‘The definition of yield strength of high-strength reinforcement for Grade 420 (Grade 60) in this Section is now, forthe first time, the same as that in ASTM specifications, except for bars with less than 420 MPa, the yield strength shall be taken as the stress corresponding to a strain of 0.35 percent Deformed and plain stainless steet wire and welded wire conforming to ASTM A1022 is now permitted to be used as concrete reinforcement, Sub-section 420.225 requires “Deformed non-presiressed longitudinal reinforcement resisting earthquake ‘moment, axial force, or both, in special moment frames, special structural walls, and all the components of special structural walls including coupling beams and wall piers” to be ASTM A706 Grade 420 (Grade 60), ASTM 615 Grade 275 (Grade 40) or Grade 420 (Grade 60) reinforcement is permitted if two supplementary Fequirements are met, which are already part of the ASTM A706 specification. A third supplementary Fequirement is now added for ASTM A615 (Grade 60) reinforcement to be permitted for use in special moment frames, special structural walls. The minimum elongation in 200 mm (8") must now be the same as that ASTM AGLS (Grade 60) reinforcement (One aspect of the Code compliance that the Association of Structural Engineers of the Philippines is cautioning Designers and Constructors alike, is the introduction of ASTM 615 Grade 520 (Grade 75) in the Philippine National Structural Code of the Philippines Volume I, 7th Edition, 1 Printing, 2016 ixrmatket, Since this was not covered by previous editions of the NSCP Vol. 1, it creates an impression of an dinregutated use of anew high-strength reinforcement grade, NSCP 7* Ealition ‘To putt clearly, Sub-setion 4202.25, corresponding to ACI 318M-14 Section 2022.5, specifies the luce of deformed nonpresiressed longitudinal reinforcement resisting carthquake-induced moment, ‘ial force, of both, in special moment frames, special structural walls, and all components of special ‘ructural walls, including coupling beams, and wall piers which shall be in accordance with (2) or (b): (a), ASTM A700M, Grade 420 (b), ASTM AGI5M, Grade 280 “There was no mention that ASTM A61SM, Grade 520, was allowed, although the use of micro-alloyed high-strength reinforcement may be allowed in the future through the issuance of a new ASTM or Updated standard, and with proper validation by the Department of Trade and Industry's Bureau of ‘Standards, It will be premature to allow its use for special moment frames, special structural wells, and fall components of special structural walls, including coupling beams, and wall piers for Buildings Tocated in arcas of high seismicity (zone 4). The same restrictions indicated in Subsection 420.7.6, on the use of quenched-tempered thermo-mechanically treated (QT/TMT) reinforcing bars in structures Tocated in seismic zone 4 for Grade 420 reinforcement, shall also be applied to Grade 520, unless proven in subsequent studies and tests. 4.13 Section 122: Sectional Strength “The following are the changes in Section 422: For prestressed members, @ new equation for the nominal axial strength at zero eccentricity has been introduced in Sub-section 422.4.2.3. ‘New Sub-section 422.4.3.1, whieh requires that the nominal axial tensile strength of a non-prestressed, ‘composite, or prestressed member, not to be taken greater than the maximum nominal axial tensile steongth of member. G14 Section 425: Reinforcement Details ‘Two changes shown in Table 7 (part of Table 425, 3.2) are made to eliminate the differences between the required tail extension of a 90-degree or 135- degree standard hook, subject to « minimum of 75. mm (3"), Mechanical or welded splices with strengths below 125% of the yield strength ofthe spliced reinforcing bars are no longer permitted. The associated stagger requirements have been deleted. Thus there is no onger a need to specify “full” mechanical or “full” welded splices 4.15 Section 426: Construction Documents and Inspection In this section, the user will probably require some time to get used to, it starts wit the following: 426.1.1 This Sub-section addresses (a) through (€): (a) Design information that the licensed design professional shall specify in the construction documents, (b) Compliance requirements that the licensed design professional shall specify in the ‘construction documents, (©) Inspection requirements that the licensed design professional shall specify in the ‘construction documents, ‘Thus, construction and inspection requirements have been consolidated, and they are now related 10 construction dacuments. The construction requirements are designated either as “design information” of “compliance requirements.” These are largely existing material that has been rearranged. ‘The ‘Association of Structural Engineers of the Philipines, inc. (ASEP) xinspection requirements in Sub-section 426.13 are taken from Chapter 17 of the 2015 International Building Code (LBC) and were previously not part of ACI 318. Provisions in ACI 318-11 and earlier editions, which explained basic statistical considerations in mixture proportioning, are no longer found in ACI 318-14, Instead, ACI 301-10, Specifications for Structural Concrete, is referenced ‘These are some other changes in the makeup of NSCP 2016 7" Edition that should be noted 1. ‘There are two new Sections: Section 40s, Structural System Requirements and Section 412, Diaphragms. Seetion 422, Structural Plain Concrete, now Section 414, 3. Section 423, Anchoring to Conerete, is now Section 417, with no significant changes. 4. Section 421, Farthquake-Resistnt Structures, now Section 418 5. Section 427, changes je Models is now Section 423, with no significant 6. Section 420, Strength Evaluation of Existing Structures, is now Section 427, 7. Section 419, Shells and Folded Plates, is now Section 428. 8, Section 424, Alternative Design Method, now Section 429, is adapted from earlier editions of the NSCP. 9, Section 425, Alternative Provisions for Reinforced and Prestressed Concrete Flexural and Compression Members, and Section 426, Alternative Load and ‘Strength Rediction Factors, have been discontinued 10, On the other hand, Section 416, Precest Concrete, and Section 418, Prestressed Concrete, no longer exist as separate entities. The provisions of these Sections are now spread over several of the new Sections Sub-seetion 418.18, Requirements for post-tensioning duets and grouting have also been removed as ‘being outdated. The Commentary now provides specification guidance. e (Chapter 5: Stuetural Stet. ASEP adapted the American Institute of Steel Construction (AISC) 14th Edition in this updated Siructural Steel code. The revisions made in this chapter are the following: ce The entire Structural Stee! chapters are streamlined placing all chapter definitions under one Definition heading, tables are immediately shown where they are first mentioned, figures drawn larger, equation ae alin boldface, extraneous user notes are removed, essential in-text definitions italicized and in-text equation terms are writen in boldface for easy reference. €2 Change of headings and terms, 5013.5 Filler Metal and Flux for Welding to 501.3.5 Consumables for Welding 510.103 Web Crippling to Web Lecal Crippling 3575 Special Fabrication Requirements, Weld tabs changed to Run-of? tabs under | Exception. i 463 Beams changed to Beams Bracing 3. Creation of new subtopic. APPENDIX A-4 | National Structural Code of the Philippines Volume I, 7th Edition, 1* Printing, 2016 xiSTRUCTURAL FIRE ‘A-423.1 ‘Thermal Elongation is ereated under A-4.2.3 Material Strengths at Elevated ‘Temperatures APPENDIX A-6 STABILITY BRACING FOR COLUMNS AND BEAMS ‘A-64 Beam-Coluran Bracing ‘SECTION 529 BUCKLING-RESTRAINED BRACED FRAMES (BRBF) ‘A section 529.3 was created as heading for 5293.1 and $293.2 ce Revision in lad factor ‘510.8 Colum Bases and Bearing on Concrete aoio, ee =0so(lAre) — 9, =251480) 2015: $e=0-650ULRFD) = . 31(08D) 5. Revision in equations 'B-5. QUALIFYING CYCLIC TESTS OF BUCKLING-RESTRAINED BRACES 511.2.2e Branches with Axil Loads in K-Connetions an} o(e gets) ro auet uaa % ca eer APPENDIX A-3 - DESIGN FOR FATIGUE. 2010: ‘A-3.4 Bolts and Toreaded Paris 1 = 2(4, 9382)? 2010: Chapter 6: Wood. 32015: ‘The revisions made in this Chapter ate the following: £1 Section 616 - Design Provisions andl Equations: The NDS 2015 Chapter 3 is adopted almost in its entirety, £2 Section 617 — Sawn Lumber: The NDS 2015 Chapter 4 is adopted almost in its entirety: £3 Section 618 ~ Structural Glued Laminated Timber: The NDS 2015 Chapter 5 is adopted almost in its entirety; {4 Tables 619.1-3 and 619.1-4 are revised based on NDS 2015; and £5 Other Sections affected are adjusted accordingly. ‘Chapter 7: Masonry ‘The revisions made in this chapter are the following: 1 The specified yild strength of ste! reinforcement is 420MPa instead of 413 MPa 415 MPa; Association of Structural Engineers of the Philippines, Inc. (ASEP) xi82 Section 7106.3 and Section 710.7.1 10mm diameter instead of No.9 gage wire g3 Section 713.9.1 20mm diameter instead of 19-page 25mm diameter instead of 24-gage Acknowledgment ; ‘The ASEP Codes and Standards Committee ate indebted to Philippine Institute of Voleanology and Seismology (PHIVOLCS) and to Dir. Renato V. Solidum, Ph. D. for his unselfish contribution specifically on Section 208 of this code. ASEP acknowledges the contribution of Dr. Teresito C. Bacoleol and Ms. Madeline Cabologan of PHIVOLCS for the seismic maps used in this code. ASEP acknowledges the contribution of Engr. Carles M, Villaraza for his unselfish contribution on Chapter 2 Seismic/Earthquake Chapter ‘The contributions of ASEP members and other users of this code who have suggested improvements, identified errors and recommended items are recognized. ASEP also acknowledges the contribution of the industry partners, companies and individuals, who continue to. support ASEP's numerous undertakings. ‘The ASEP Codes and Standards Committee also acknowledge Arch. Avigaile Genota Riola who designs the covers ‘of the NSCP Volume 1, 2010 Edition and NSCP Volume 1, 2015 Edition, National Structural Code of the Philippines Volume J, 7th Edition, * Printing, 2016 ilNSGP 101-15 Chapter 1 GENERAL REQUIREMENTS NATIONAL STRUCTURAL CODE OF THE PHILIPPINES VOLUME I BUILDINGS, TOWERS AND OTHER VERTICAL STRUCTURES SEVENTH EDITION, 2015 Association of Structural En; Suite 713, Future Point Plaza Condo1 142 Panay Avenue, Quezon City, Philippines 1100 ers of the Philippines, Inc. ‘Tel. No. : (+632) 410-0483 Fax No. : (+632) 411-8606 Email: [email protected] ‘Websitechttp:/iwww.asepontine.org National Structural Code of the Philippines Volume J, 7th Edition, 2015CHAPTER 1 ~ General Requirements 1-4 Table of Contents SECTION 101... ‘TITLE, PURPOSE AND SCOP! 101.1 Special Foundation Systems... 101.2 Purpose.. a 101.3 Scope. 101.4 Alternative Systems, SECTION 102. ae DEFINITIONS. ons auReaeaa aoa SECTION 103. CLASSIFICATION ese OF STRUCTURES 103.1 Nature of Occupancy. SECTION 104 DESIGN REQUIREMENTS.. 104.1 Surength Requirement. 1042 Serviceability Requirement 104.3 Analysis. : 106.4 Foundation Investigation... 1045 Design Review. SECTION 108. a POSTING AND INSTRUMENTATION, 105.1 Posting of Live Loads. 105.2 Earthquake-Recording Instrumentation ncn. SECTION 106... fas SPECIFICATIONS, DRAWINGS AND CALCULATIONS 106.1 General 106.2 Specifications 1063 Design Drawings, SECTION 107. oo STRUCTURAL INSPECTIONS, T 107.1 General 1072 Definitions 107.3. Structural Inspector.. 107.4 Inspection Program .. Riel a 107.5 Types of Work for Inspection 7 Policia ttt aithdtied tth 107.6 Approved Fabricators sia ACAI TS AND STRUCTURAL OBSERVATION: ee ee : 8 | 1077 Preibrieted Construction : eee SB a 107.8 Non-Destructive Testing. tnevennstattttrnererneneseenesees ota rane z - venee 14 | 1079) Sisal Observation : See eee | APPENDICES 3 1-4 ~ Recommended Guidelines on Structural Design Peer Review of Structures 2015. TA-1 FA Guidlines and Implementing Rules on Eartha Recording Instrumentation fo Buin. Il National Structural Code ofthe Philippines Volume I, 7th Edition, 20151-2 CHAPTER t - General Requirements URPOSE AND SCOPE 101.1 Special Found: 1 Systems ‘These regulations shall be known as the National Structural Code of the Philippines 2015, Volume 1, 7th Edition, and may be cited as such and will be referred © herein as “this code.” 101.2 Purpose ‘The purpose of this code is to provide minimam requirements for the design of buildings, towers and other vertical structures, and minimum standards and guidelines to safeguard life or limb, property and public welfare by regulating and contolling the design, construction, ‘quality of materials pertaining to the structural aspects of all buildings and structures within ths jurisdiction. 1013 Scope ‘The provisions of this code shall apply to the construction alteration, moving, demolition, repair, maintenance and use ‘of buildings, towers and other vertical structures within this Jurisdiction, Special structures such as but not limited to single family dwellings, storage silos, liquid product tanks and hydraulic flood control structures, should be referred to special state of practice literature but shall refer to provisions of this code as a minimum wherever applicable. For additions, alterations, maintenance, and change in use of buildings and structures, see Section 108. Where, in any specific case, different sections of this code specify different materials, methods of construction oF other requirements, the most restrictive provisions. shall govern except in the case of single family chwellings. Where there is a conflict between a general requirement and a specific requirement, the specific requirement shall be applicable. 101.4 Alternative Systems ‘The provisions of this code are not intended to prevent the use of any material, altemate design or method of construction not specifically prescribed by this code, provided any alternate has been permitted and its use ‘authorized by the Building Official (see Section 102). Sponsors of any system of design or construction not within the scope of this code, the adequacy of which had been shown by successful use and by analysis and test, shall have the right (0 present the data on which their design is based to the Building Official or to a board of ‘examiners appointed by the Building Official or the project, ‘owner/developer. This board shall be composed of ‘competent structural engineers and shall have authority £0 investigate the data so submited, to require tests if any, and to formulate rules governing design and construction of such systems to meet the intent of this code. These rules, when approved and promulgated by the Building Official, shall be of the same force and effect as the provisions of this code ‘Association of Structural Engineers of the Philippines, Inc. (ASEP)SECTION 102 DEFINITIONS. For the purpose of this code, certain terms, phrases, words and their derivatives shall be construed as specified in this chapter and elsewhere in this code where specific definitions are provided. Terms, phrases and words used in the singular include the plural and vice versa, Terms, phrases and words used in the masculine gender inelude the eminine and vice versa, The Following terms are defined for use inthis code: ALTER or ALTERATION is any change, addition or modification in construction or occupancy. APPROVAL shall mean that the proposed work or completed work conforms to this code in the opinion of the Building Official APPROVED as to materials and types of construction, refers to approval by the Building Official as the result of investigation and fests conducted by the Building Offical, or by reason of accepted principles or tests by recognized authorities, technical or scientific organizations. AS GRADED is the extent of surface conditions on completion of grading, AUTHORITY HAVING JURISDICTION is the ‘organization, political subdivision, office or individual charged with the responsibility of administering and enforcing the provisions of this code. BEDROCK is in-place solid or altered rock, BENCH is a relatively level step excavated into earth material on which fill is to be placed. BORROW is earth material acquired from an off-site location for use in grading on a site. BUILDING is any structure usually enclosed by walls, and a roof, constructed to provide support or shelter for an intended use or occupancy. BUILDING, EXISTING is building erected prior to the adoption of this code, or one for which a legal building permit has been issued. CHAPTER 1 ~ General Requirement 1-3, BUILDING OFFICIAL is the officer or other designated authority charged with the administration and enforcement of this code, of the Building Officia's duly authorized representative. CIVIL ENGINEER isa professional engineer licensed to practice inthe Field of civil engineering. CIVIL ENGINEERING is the science or profession in which a knowledge of the mathematical and physical sciences gained by study and practice is applied with judgement to utilize natural and man-made resources and forces in the planning, design, management, construction, and maintenance of buildings, structures, facilities, and utilities in their totality, for the progressive well-being and for the benefit of mankind, enhancing the environment, ‘community fiving, industry, and transportation, taking into consideration such aspects as functionality, efficiency, economy, safety, and environmental quality COMPACTION jis the densification of a fill by ‘mechanical or chemical means, CONSTRUCTION FAILURE is a failure that occurs during construction and they are considered (o be either a collapse or distress, of a structural system to such a degree that it cannot safely serve its intended purpose.’ CONTINUOUS STRUCTURAL INSPECTION is a structural inspection where the structural inspector is on the site at all times observing the work requiring structural inspection, EARTH MATERIAL is any rock, natural soil or fill of any combination thereof, ENGINEER-OF-RECORD is a civil engineer responsible for the structural design, EROSION js the wearing away of the ground surfs result of the movernent of wind or water EXCAVATION is the mechanical removal of earth material EXISTING GRADE is the grade prior to grading. FAILURE is defined as an unacceptable difference between expected and observed performance. This, definition includes catastrophic structural collapse, but also includes performance problems that are not necessarily catastrophic or life-threatening, including “serviceability problems such as distress, excessive deformation, premature deterioration of materials, leaking coofs and facades, and inadequate interior environmental control systems." In the event of a significant failure, the parties typically retain experts to determine the cause of the perceived failure. Occasionally a failure results from a "National Structural Code of the Philippines Volume I, 7th Edition, 20154-4 CHAPTER 1 ~ General Requirements single condition, but typically, failures result from a combination of mistakes. oversights, miscommunications, misunderstandings, ignorance, lapses, slips, incompetence, intentional violations or non-compliance, and inadequate ‘quality assurance. The causes for these conditions vary, but nay include simple mistakes (such as sending information toa structural engineer when it should have been sent (0 the architect), conclusions based on faulty assumptions, an temployee’s “laziness, ignorance, or malevolent urge.” fatigue from excessive workload, inadequate training, “time oxing” practices used 10 minimize fees to a client, foverrelisnce on computer-aided design and drafting {CADD), failure to understand and deliver client requitements, time pressutes to a deliver a project by certain deadlines, and ineffective coordination and integration of the design team.” FILL is a deposit of earth material placed by artificial means. FINISH GRADE js the final grade of the site that conforms to the approved plan. FORENSIC ENGINEERING is the application of the art and science of engineering in the jurisprudence system, requiring the services of legally qualified engineers. Forensie engineering may include investigation of the physical causes of accidents and other sources of claims and litigation, preparation of engineering reports, testimony at hearings and trials in administrative or judicial proceedings, and the rendition of advisory opinions to assist the resolution of disputes affecting life or property GENERAL COLLAPSE is the immediate, deliberate demolition of an entire structure by a triggering event (e.g explosion).” GEOTECHNICAL ENGINEER is a registered Civil Engineer with special qualification in the practice of Geotechnical Engineering as recognized by the Board of Civil Engineering of the Professional Regulation Commission as endorsed by the Specialty Division of Geotechnical Engineering of the Philippine Institute of Civil Engineers (PICE), GEOTECHNICAL ENGINEERING is the application of the principles of soil and rock mechanics in the investigation, evaluation and design of civil works involving the use of earth materials and foundations and the Inspection or testing of the construction thereof. GRADE js the vertical location of the ground surface. GRADING is an excavation or ‘or combination thereof. KEY is a designed compacted fill placed in a trench excavated in earth material beneath the toe ofa slope. LIMITED LOCAL COLLAPSE is a failure of & structural member without affecting the adjacent members ea. destruction of one oF to columns in a muli-bay structure)! OCCUPANCY — is the purpose for which a building or other structures or part thereof, is used or intended to be used. PERIODIC STRUCTURAL INSPECTION is a structural inspection where the inspections are made on a periodic basis and satisfy the requirements of continuous, inspection, provided this periodic scheduled inspection is performed as outlined in the inspection program prepared by the structural engineer. PREFABRICATED ASSEMBLY is a structural unit, the integral parts of which have beea built up or assembled prior to incorporation in the building, PROFESSIONAL INSPECTION is the inspection required by this code to be performed by the civil engineer. Such inspections include that performed by persons supervised by such engineer and shall be sufficient to form ‘an opinion relating to the conduct of the work PROGRESSIVE COLLAPSE is the spread of an initial local failure from element to element, eventually resulting in the collapse of an entire structure or disproportionately large part of t./ ROBUSTNESS is the insensibility of a structure to local failure, From this definition, it follows that the robustness isa property of the structure. ROUGH GRADE js the stage at which the grade approximately conforms to the approved plan, SITE is any lot or parcel of land or contiguous combination theceof, under the same ownership, where grading is performed or permitted. SLOPE is an inclined ground surface the inclination of which is expressed as a ratio of vertical distance 10 horizontal distance, SOIL is naturally occurring superficial deposits overlying, bedrock. SOILS ENGINEER See Geotechnical Engineer. SOILS ENGINEERING See Geotechnical Engineéring. STRUCTURE _ is that which is built or constructed, an edifice or building of any kind, or any piece of work artificially built up or composed of parts joined together in, some definite manner. Association of Structural Engineers of the Philippines, Inc. (ASEP) bela i i 8 LAN ASrE Mui SBAMCSONUG eH ENS Be associ Osa cw ENS eSB NOMASTRUCTURAL ENGINEER is a registered Civil Engineer with special qualification in the practice of Structural Engineering as recognized by the Board of Civil Engineering of the Professional Regulation Commission or by the Specialty Division of the Philippine Institute of Cvit Engineers (PICE) together with the Association of Structural Engineers of the Philippines (ASEP) and Institution of Specialise. Structural Engineers. of the Philippines ('SSEP). STRUCTURAL ENGINEERING is a discipline of civil engineering dealing with the analysis and design of structures that support or resist loads insuring the safety of the structures against natural forces, STRUCTURAL FAILURE is the reduction of capability ‘ofa structural system or component (0 such a degeee that i ‘cannot sally serve its intended purpose. * ‘Structural failures can be divided into various categories based on consequential damages to include: Catastrophic Failure with Loss of Life, Catastrophic Failure in which No Human Lives ore Endangered, Failure Resulting in Extensive Property Damage, and Failure Resulting in Reduced Servicenbility.? STRUCTURAL INSPECTION is the visual observation bya structural inspector of a particular type of construction work or operation for the purpose of ensuring its general compliance to the approved plans and specifications and the applicable workmanship provisions of this code as well as overall consiruetion safety at various stages of construction STRUCTURAL OBSERVATION isthe _ visual observation of the structural system by the structural observer as provided for in Section 107.9.2, for its general conformance to the approved plans and specifications, at significant construction stages and at completion of the Structural system. Structural observation does not include or waive the responsibility for the struetural inspections required by Section 107.1 or other sections of this code. TERRACE js a relatively level step constructed in the face of a graded slope surface for drainage and maintenance purposes, {Guido ineigton of Src Fates ASCE: 186 °F American Sty of Cl Enger (ASCE Tec Couel Ferri Egg 2 Farensie Engineering, 2 Edition, Keneth l, Carper, Editor, 2001 “ Robusmess of Buildings in Structural Codes, Dinitris Diamant, fom 5 serra Fates gs, ASCE, 181, Se CHAPTER 1 ~ Gonerol Requirement "National Structural Code of the Philippines Volume |, 7th Edition, 2015 484.8 CHAPTER 1 ~ General Requirements SECTION 103 CLASSIFICATION OF STRUCTURES 103.1 Nature of Occupancy Buildings and other structures shall be classified, based on the nature of occupancy, according to Table 103-1 for purposes of applying wind and earthquake loads in Chapter 2. Each building ot other structures shall be assigned to the highest applicable occupancy category or categories. ‘Assignment of the same structure to multiple occupancy ‘categories based on use and the type of loading condition being evaluated (c.g. wind or seismic) shall be permissible. When buildings or other structures have multiple uses (occupancies) the relationship between the uses of various parts of the building or other structure and the independence of the structural system for those. various parts shall be examined. The classification for each independent structural system of a multiple-use building ot ‘other structure shall be that of the highest usage group in any part of the building or other structure that is dependent fon that basie structural system, ‘Table 103-1 Occupaney Category OCCUPANCY | OCCURANCY OR FUNCTION OF CATEGORY _| STRUCTURE COcoupaneles having surgery and emergency reameat ares, Fire on police sation Garages and sholiare For omergeny vehicles and merge ata, ‘Surette and sheers in emergency proparsiness Avion con towers Seustures and equipment in conmaication fears and other Files rogue for emergency 1 esseatia | psponse ss Facies Foeilites for standby power-generating equipment for Category sete, “Tanks or ar stuctres contining housing oF oppoting water rather re-sappression atrial fr cipriat required for the. protection of {Category oe, TV and V stewie Pablieseioa uildings. Hospi, Designated evacuation center and Power and communication ansmission ines Ocsupunsis and ster housing or supporing toxic or explosive comizals or subsiness, M1 Hazardous Thales, | Non-tuilding strwetwes storing, supporting or ‘quinties of toxe oF explsive ‘Association of Structural Engineers of the Philippines, Inc. (ASEP)Table 103-1 (cont’d)Occupancy Category ‘OCCUPANCY CATEGORY, ‘OCCUPANCY OR FUNCTION OF STRUCTURE, UN Speci Oceupaney Structures Buildings wid) an assembiy room with an ‘occupant eapaciy of 1,000 or more Educational uikings such 26 museums, Tears, aioe wily 9 copy of 30) or more aecpanis Bulg: used foe college or aul edveation with capacity oF $00 oF more ossupants Insivtinal buildings with $0 of more Incspacitued patients, Gu et secluded in Category Ment hospitals, saitaiuns, jis prisons tnd other lings hee personal Herts inmates are sniaty retina CChurees, Mosques, and ther Religion Facies, All structures with an occupaney of 8,000 oe ore persons, Stretures and equiprent in power-generating stations, another pubic uly faeiltes sat ‘nluded in Category Tor Category Il and quired for contined operation, WV Standard Occupancy Struc All structures housing occupancies or havingfanetionsnotlistedioCategory |, 11 olflandCategory, Y. Miscstancous Stractares Privatewarages.carpors shedsand fences ‘over | Smhigh CHAPTER 1 - Generel Requirement 1-7 104.1 Strength Requirement Buildings, towers ond other vertical structures and all portions thereof shall be designed and constructed to sustain, within the limitations specified in this code, all loads set forth in Chapter 2 and elsewhere in this code, combined in aceordance with Section 203, Design shall be in accordance with Strength Design, Load and Resistance Factor Design and Allowable Stength Design methods, as permitted by the applicable material chapters. 104.2 Serviceability Requirement 1042.1 General ‘Structural systems and members thereof shall be designed to have adequate stiffness to limit deflections, lateral drifts, vibration, or any other deformations that adversely affect the intended use and performance of buildings, towers and. ‘other vertical structures. The design shall also consider durability, resistance to exposure to weather or aggressive environment, crack control, and other conditions that affect the intended use and performance of buildings, towers and other vertical structures, 1043 Analysis, Any system or method of construction to be used shall be based on a rational analysis in accordance with well established principles of mechanics that take into account equilibrium, general stability, geometric compatibility and both short-term and long-term material properties. Members that tend to accumulate residual. deformations ‘under repeated service loads shall have included in their analysis the added eccentricities expected to accur di ticir service life. Such analysis shall result in a system that provides a complete load path capable of transferring all loads and forces fiom their point of origin to the load. resisting elements. The analysis shal include, but not be limited “to, the provisions of Sections "1043.1 through }04.3.3, 104.3.1 Stability against Overturning Every structure shall be designed to resist the overturning effects caused by the lateral forces specified with adequate Factor of Salety (FOS). See Section 206.6 for retaining walls, Section 207 for wind loading and Section 208 for earthquake loading, National Structural Code of the Philippines Volume I, 7th Edition, 2015,4-8 CHAPTER 1 ~ General Requirements 1043.2 Self-Str ining Forces Provisions shall be made for anticipated self-straining forces arising fom differential settlement of foundations and from restrained dimensional changes due to temperature, moisture, shrinkage, heave, creep and similar effects 1043.3 Anchorage Anchorage of the roof to walls and columns, and of walls and columns to foundations shall be provided and adequately detailed to resist the uplift and sliding forces that result from the application of the prescribed forces. Concrete and masonry walls shall be anchored to all floors, roofs and other structural elements that provide lateral support for the wall. Such anchorage shall provide a positive direct connection capable of resisting the horizontal forces specified in Chapter 2 but not less than the minimum forces in Section 206.4. 104.4 Foundation Investigation Soil explorations shall be required for buildings, towers and fther vertical structures falling under Categories 1, 1,1 and IV in accordance with Table 103-1 or as required by the Building Official or if the site specific conditions ‘make the foundation investigation necessary. Detailed requirements for foundation investigations shall be n accordance with Chapter 3 ofthis code. 104.5 Design Review ‘The design calculations, drawings, specifications and other design-related documents for buildings, towers and other vertical structures with irregular configuration in ‘Occupancy Categories 1, II or IIL within Seismic Zone 4, structures under Alternative Systems in Section 101.4, and Undefined Structural Systems not listed in Table 208-11, shall be subject to a review by an independent recognized structural engineer or engineers 1o be employed by the owner in accordance with the ASEP Design Peer Review Guidelines. The structural engineer or structural ‘engineers performing the review shall have comparable qualifications and experience as the structural engineer responsible for the design. The reviewer or reviewers shall obtain a professional waiver from the engineer-of-ecord who shall be expected to grant such waiver in keeping with ethical standards of the profession as adopted in ASEP guidelines for peer review (Appendix |-A), The design review shall, as a minimum, verify the general compliance with this code which shall include, but not be limited to, the review of the design load criteria, the design concept, mathematical model and techniques. ‘The following may also be verified, that there are no major errors in pertinent calculations, drawings and specifications and may also ensure that the structure as reviewed, meet ‘minimum standards for safety, adequacy and acceptable standard design practice. The engineer-of-secord shall submit the plans and specifications, a signed and sealed statement by the structural engineer doing the review that the above review has been performed and that minimum standards have been met, See Section 208.5.3.6.3.2 for design review requirements \when nonlinear time-history analysis is used for earthquake design Jn keeping with the ethical standards of the profession, the reviewer or reviewers shall not supplant the engineer-of- record as engineer-oF-record for the project, The design review shall not in any way transfer or diminish the responsiblity of the engineer-ot-record. ‘Association of Structural Engineers of the Philippines, inc. (ASEP)105.1 Posting of Live Loads ‘The live loads for which each floor or portion thereof of commercial or industrial building has been designed shall have such design live londs conspicuously posied by the ‘owner in that part of each story in which they apply, using durable metal signs. It shall not be allowed to remove or deface such notices. The occupant of the building shall be responsible for keeping the actual load below the allowable limits 105.2 Earthquake-Recording Instrumentation 1052.1 General Unless waived by the Building Official, every building in Seismic Zone 4 over 50 m in height shall be provided with, not less than three approved Earthquake Recording Instruments (ERI). ‘The ERI shall be interconnected for ‘common start and common timing. Please refer to “ASEP Guidelines and Implementing Rules on Earthquake Recording Instrumentation for Buildings (Appendix 1-B), 10522 Location ‘The instruments shall be located in the basement, ‘midportion, and near the top of the building. Each instrument shall be located so that access is maintained at all times and is unobstructed by room contents. A sign stating “MAINTAIN. CLEAR ACCESS TO THIS. INSTRUMENT” shall be posted in a conspicuous location 105.23 Maintenance Maintenance and service of the instruments shall be provided by the owner of the building, subject to the monitoring of the Building Official. Data produced by the instruments shall be made available (o the Building Official or any authorized agency upon request, 108.24 Instrumentation of Selected Buildings All owners of existing structures selected by the authorities having jurisdiction shall provide accessible space for the installation of appropriate earthquake ‘ecording instruments, determined by a Structural Engineer CHAPTER 1 General Roquirement 7-9 SECTION 106~ -ECIFICATION 106.1 General Copies of design caleulations, reports, plans, specifications and inspection program for all, constructions shall bear the signature and seal of the cengineer-of-record. 106.2 Specifications ‘The specifications shall contain information covering the material and construction requirements. The materials and construction requirements shall conform to the. specifications refered to in Chapters 1 to 7 ofthis code, 106.3 Design Drawings 1063.1 General ‘The design drawings shall be drawn to scale on durable paper or cloth using permanent ink and shall be of sufficient clarity to indicate the location, nature and extent of the work proposed.The drawings shall show a complete design with sizes, sections, relative locations and. connection details of the various members. Floor levels, column centers and offsets shall be dimensioned, Where available and feasible, achive copies shall be maintained in durable medium such as compact dise (CD) and digital versatile dise (DVD), 1063.2 Required Information “The design drawings shall contain, but shall not be limited to the general information listed in Seetion 106.321 and material specific information listed in Sections 1063.22 and 106,3.2.3, as applicable 1063.21 General Information 1 Name and date of issue of building code and supplements, if any, o which the design conforms. 2. Strengths or designations of materials to be used. 3. Design strengths of underlying soil or rock. The soil or rock profile, when available, shall be provided. 4. Live loads and other loads used in design and clearly indicated inthe floor plans. "National Structural Code of the Philippines Volume |, 7th Eaitlon, 2015