1.3.

1 Softwoods

Softwoods, characterised by having naked seeds or as cone-bearing trees, are generally

evergreen with needle-like leaves (such as conifers) comprising single cells called

tracheids, which are like straws in plan, and they fulfil the functions of conduction

and support. Rays, present in softwoods, run in a radial direction perpendicular to the

growth rings. Their function is to store food and allow the convection of liquids to where

they are needed. Examples of the UK grown softwoods include spruce (whitewood),

larch, Scots pine (redwood) and Douglas fir.

[Link] Softwood characteristics -

Quick growth rate (trees can be felled after 30 years) resulting in low-density

timber with relatively low strength.

Generally poor durability qualities, unless treated with preservstrengt

Due to the speed of felling they are readily available and comparatively cheaper.

1.3.2 Hardwoods

Hardwoods are generally broad-leaved (deciduous) trees, which often lose their leaves

at the end of each growing season. The cell structure of hardwoods is more complex than

that of softwoods with thick-walled cells, called fibres, providing the structural support and thin-walled
cells, called vessels, providing the medium for food conduction. Due

to the necessity to grow new leaves every year the demand for sap is high and in some

instances larger vessels may be formed in the springwood, these are referred to as

‘ring-porous’ woods such as in oak and ash. When there is no definite growing period

the pores tend to be more evenly distributed, resulting in ‘diffuse-porous’ woods such

as in poplar and beech. Examples of the UK grown hardwoods include oak, beech, ash,

alder, birch, maple, poplar and willow.

[Link] Hardwood characteristics -

Hardwoods grow at a slower rate than softwoods, which generally results in a

timber of high density and strength, which takes time to mature, over 100 years

in some instances.
-

There is less dependence on preservatives for durability qualities.

Due to the time taken to mature and the transportation costs of hardwoods, as most

are tropical, they tend to be expensive in comparison with softwoods.

British Standard BS 5359:1991 [3] provides a list of some 500 timbers of economic

interest in the United Kingdom and tabulates softwoods and hardwoods including their

standard names, botanical names/species type and also, where relevant, their alternative

commercial names with sources of supply and average densities.

Reaction wood

Reaction wood is referred to abnormal wood tissues produced in tree trunks subjected to

strong wind pressures. Horizontal branches and leaning branches are believed to form

reaction wood in an attempt to prevent them from excessive bending and cracking under

their own weight. There are two types of reaction wood: in softwoods it is referred to as

compression wood and in hardwoods as tension wood. Compression wood, Figure 1.2,

forms on the underside of branches of leaning softwoods and contains more lignin

than normal wood. Tension wood forms on the upper sides of leaning hardwoods and

contains more cellulose than normal wood.

Reaction wood is much denser than normal wood with the specific gravity of around

35% greater in compression wood and 7% greater in tension wood. Longitudinal shrink-

age is also greater, 10 times more than normal for compression wood and 5 times for

tension wood. Timber containing compression wood is liable to excessive distortion during drying and
tends to fail in a brittle manner. It is harder to drive a nail in com-

pression wood, there is a greater chance of it splitting, and compression wood may

take a stain differently than normal wood. Most visual strength grading rules limit the

amount of compression wood in high quality grades.

Juvenile wood
This is a wood that is produced early in the first 5–20 rings of any trunk cross-section

(Figure 1.1) and, in general, exhibits lower strength and stiffness than the outer parts of

the trunk and much greater longitudinal shrinkage than mature, normal wood. Juvenile

wood is mainly contained within the heartwood. In this regard, in young, fast grown

trees with a high proportion of juvenile wood, heartwood may be inferior to sapwood,

but is not normally considered a problem.

Visual grading

Visual grading is a manual process carried out by an approved grader. The grader

examines each piece of timber to check the size and frequency of specific physical

characteristics or defects, e.g. knots, slope of grains, rate of growth, wane, resin pockets

and distortion.

The required specifications are given in BS 4978 and BS 5756 to determine if a piece

of timber is accepted into one of the two visual stress grades or rejected. These are

general structural (GS) and special structural (SS) grades. Table 2 of BS 5268-2:2002

[10] (reproduced here as Table 1.2) refers to main softwood combinations of species

(available in the United Kingdom) visually graded in accordance with BS 4978:1996

[8].

1.5.2 Machine grading

Machine grading of timber sections is carried out on the principle that stiffness is

related to strength; where the relationship between the modulus of elasticity, E, and

the modulus of rupture of a species of timber from a certain geographical location is

determined from a statistical population, based on a substantial number of laboratory

controlled tests. There are a number of ways for determining the modulus of elasticity,

including resonant vibration (dynamic response), but the most common methods are

either load- or deflection-controlled bending tests. The machine exerts pressure and

bending is induced at increments, along the timber length. The resulting deflection (orTable 1.2
Softwood combinations of species and visual grades that satisfy the

requirements for various strength classes∗

∗Timber graded in accordance with BS 4978:1996; based on Table 1.2, BS 5268-2:2002.

the load to induce a known deflection) is then automatically measured and compared

with pre-programmed criteria, which leads to the direct grading of the timber section

and marking with the appropriate strength class. An example of the grading marking,

based on the requirements of BS EN 14081-1:2005, is shown in Figure 1.7.

In general less material is rejected if machine graded; however, timber is also visually

inspected during machine grading to ensure that major, strength-reducing, defects do

not exist.

Environmental sustainability has become a global concern. Countries and

corporations are becoming more aware of the damage they cause, and are
looking for ways to mitigate the harm. Construction procedures and materials
can harm the environment, and this has spurred an interest in developing
environmentally friendly techniques and materials.

Individuals, companies and governments are striving to improve the

environmental performance of their buildings and the materials used.
Buildings represent 35-40% of US energy consumption and a similar
percentage of the national carbon emissions. Green construction is key for
sustainability and to mitigate environmental damage.

Carbon dioxide is the primary gas emitted from human activity and the best-known greenhouse gas
contributing to global warming. Every time we start a car, flip on a switch, or use anything
associated with petroleum, coal, natural gas, or electricity, we emit carbon dioxide into the air.
The overabundance of carbon dioxide in the atmosphere causes more heat to be trapped, increasing
temperatures that result in global warming.
Destruction of Carbon Sinks
It would be naïve to say that greenhouse gas emissions are the sole cause for extra heat trapped in
the atmosphere. Unfortunately, our human contributions to this problem don’t stop there; when we
destroy natural resources like forests, we remove the raw materials that help to absorb the emitted
gases.
Carbon sinks are beneficial areas where more carbon dioxide is removed from the atmosphere and
stored in plants and trees than is emitted. Deforestation is causing the destruction of natural sinks,
leaving less plant life to absorb carbon dioxide. According to the EPA, land use and forestry
management allowed for a 15% offset of greenhouse gas emissions in 2010
Moisture Content and Shrinkage

The solid portion of wood is made of a complex cellulose-lignin compound. The

cellulose comprises the framework of the cell walls, and the lignin cements and

binds the cells together.

In addition to the solid material, wood contains moisture. The moisture content

(MC) is measured as the percentage of water to the oven dry weight of the wood:

The moisture content in a living tree can be as high as 200 percent (i.e., in some

species the weight of water contained in the tree can be 2 times the weight of

the solid material in the tree). However, the moisture content of structural

lumber in service is much less. The average moisture content that lumber

assumes in service is known as the equilibrium moisture content (EMC).

Depending on atmospheric conditions, the EMC of structural framing lumber

in a covered structure (dry conditions) will range somewhere between 7 and 14 percent. In most cases,
the MC at the time of construction will be higher than

the EMC of a building (perhaps 2 times higher). See Example 4.1.

Moisture is held within wood in two ways. Water contained in the cell cavity

is known as free water. Water contained within the cell walls is known as bound

water. As wood dries, the first water to be driven off is the free water. The mois-

ture content that corresponds to a complete loss of free water (with 100 percent

of the bound water remaining) is known as the fiber saturation point (FSP). No

loss of bound water occurs as lumber dries above the fiber saturation point. In

addition, no volume changes or changes in other structural properties are asso-

ciated with changes in moisture content above the fiber saturation point.

However, with moisture content changes below the fiber saturation point, bound

water is lost and volume changes occur. If moisture is lost, wood shrinks; if mois-

ture is gained, wood swells. Decreases in moisture content below the fiber

Properties of Wood and Lumber Grades 4.13

EXAMPLE 4.1 Bar Chart Showing Different MC Conditions

Figure 4.5 shows the moisture content in lumber in comparison with its solid weight. The

values indicate that the lumber was manufactured (point 1) at an MC below the fiber

saturation point. Some additional drying occurred before the lumber was used in con-

struction (point 2). The EMC is shown to be less than the MC at the time of construc-

tion.

Shrinkage of Lumber

The Wood Handbook (Ref. 4.20) lists average clear wood shrinkage percentages for many

individual species of wood. Tangential shrinkage is greatest. Radial shrinkage is on the

order of one-half of the tangential value, but is still significant. Longitudinal shrinkage

is small and is usually disregarded.

Figure 4.6a Seasoning checks

may occur in the wide side of a

member at or near the neutral

axis. These cracks form because

wood near the surface dries and

shrinks first. In larger pieces of

lumber, the inner core of the

member loses moisture and

shrinks much slower. Checking

relieves the stresses caused by

nonuniform drying.