2/12/2021 Soviet portable scope C1-118
Ads by
Stop seeing this ad Why this ad?
BLDC Motor Control Solutions
Looking how to get brushless motors under control? Discover ST's
solutions.
STMicroelectronics Down
Soviet portable scope C1-118
The C1-118 (S1-118 / С1-118) oscilloscope was produced in the USSR in 1982 - 1988. It is a small portable 2-channel analog oscilloscope with a 10 MHz bandwidth. There
was also an enhanced version C1-118A (S1-118A / С1-118А) with a 20 MHz bandwidth produced in 1988 - 1989.
The C1-118 and C1-118A oscilloscopes weigh only 3.8 kg (without accessories). The width is 21cm, height 12cm, depth 33cm. The input impedance of both channels is 1
Megaohm, 20 pF. Vertical sensitivity from 5mV to 10V per division, +/- 5% accuracy. The time base horizontally is 50ns - 50ms / div in C1-118 and 20ns - 50ms / div in C1-118A.
It has +/- 5% accuracy. The CRT tube is soviet oscillographic 11LO9I (11ЛО9И) with electrostatic deflection, a useful 8 x 6 cm screen area, 6.3V 80-100mA heater and 8kV anode
voltage. The scope has brightness and beam focus knobs, horizontal trace alignment, vertical alignment of each trace. Synchronization level setting, rising / falling edge trigger switch,
external / internal sync switch, TV / NORM switch, and YI or YII channel sync switch. Each channel can be switched off to use only the other. Input for external (EXT) sync and
grounding socket. Adjustments of Y amplifiers and the timebase are accessible from the outside (from top and from sides). It has power switch and indicator lamp. You can choose
between two multiplex modes of the channels when using two traces (chopper / alternate). It is powered from 220V 50Hz-60Hz mains, it says 28VA consumption, I measured 23W.
My piece comes from 1988, originally used as a school aid, fully functional. The protective cover for the front panel is missing.
C1-118 schematic part 1 - CRT, high voltage inverter, deflection plate drivers, brightness, focus
(slightly different version with resistor and capacitor values)
C1-118 schematic part 2 - time base and triggering
(different version, probably C1-118A)
C1-118 schematic part 3 - vertical amplifiers (Y), trace switching, mains power supply
(slightly different version, poor image quality, but with resistor and capacitor values)
Oscilloscope C1-118 (S1-118 / С1-118) in operation both channels.
[Link]/c1-118_en.html 1/6
2/12/2021 Soviet portable scope C1-118
Scope C1-118 (S1-118 / С1-118) - just one channel used.
C1-118A (S1-118A / С1-118А) - the successor of C1-118. The bandwidth was raised to 20MHz, one more position was added to the time base selector (0.02 us / div) and the
external trigger connector was replaced with BNC.
[Link]/c1-118_en.html 2/6
2/12/2021 Soviet portable scope C1-118
Oscilloscope C1-118 (S1-118 / С1-118). Similar to C1-118A (S1-118A / С1-118А).
Oscilloscope C1-118 shows 9V 50Hz sine wave (Y 5V/div, X 5ms/div).
[Link]/c1-118_en.html 3/6
2/12/2021 Soviet portable scope C1-118
Scope C1-118 (S1-118 / С1-118) from the side.
C1-118 (S1-118 / С1-118) from back.
[Link]/c1-118_en.html 4/6
2/12/2021 Soviet portable scope C1-118
Oscilloscope C1-118 (S1-118 / С1-118) made in 1988.
Scope C1-118 (S1-118 / С1-118) from bottom.
For sale 880,000 EUR, Prague 6
6 bedrooms, 7 bathrooms, 86m2 living room, interior pool 40m2, w
garden, terraces.
[Link] O
[Link]/c1-118_en.html 5/6
2/12/2021 Soviet portable scope C1-118
Added: 30. 9. 2015
home
[Link]/c1-118_en.html 6/6
