DATA SHEET

TFT COLOR LCD MODULE

NL6448BC20-08
17 cm (6.5 type), 640 × 480 pixels 262144 colors,
high luminance, wide viewing angle

DESCRIPTION
NL6448BC20-08 is a TFT (thin film transistor) active matrix color liquid crystal display (LCD) comprising
amorphous silicon TFT attached to each signal electrode, a driving circuit and a backlight. NL6448BC20-08 has a
built-in backlight. Backlight includes long-life lamps and the lamps are replaceable.
The 17 cm diagonal display area contains 640 × 480 pixels and can display 262144 colors simultaneously.
NL6448BC20-08 is suitable for industrial application use, because the luminance is high, and the viewing
direction is selectable with display scan select.

FEATURES
• High luminance (300 cd/m2, typ.)
• Low reflection
• Wide viewing angle with retardation film (Antiglare treatment)
• Display reverse scan function
• 6-bit digital RGB signals
• Edge type backlight with long-life-lamps (Two lamp holders, inverter-less)
• Variable luminance control
• Recommended inverter (Part No. 65PWB31)
• Compatible to the mounting holes position of NL6448AC20-06 except for inverter.

APPLICATIONS
• Measuring instruments
• Display terminals for control system
• Monitors for process controller

Document No. EN0442EJ1V0DS00 (1st edition)

Date Published July 1999 P
Printed in Japan © 1999
 NL6448BC20-08

STRUCTURE AND FUNCTIONS

A color TFT (thin film transistor) LCD module is comprised of a TFT liquid crystal panel structure. LSIs for driving
the TFT array, and a backlight assembly. The TFT panel structure is created by sandwiching liquid crystal material
in the narrow gap between a TFT array glass substrate and a color filter glass substrate. After the driver LSIs are
connected to the panel, the backlight assembly is attached to the backside of the panel.
RGB (red, green, blue) data signals from a source system is modulated into a form suitable for active matrix
addressing by the onboard signal processor and sent to the driver LSIs which in turn addresses the individual TFT
cells.
Acting as an electro-optical switch, each TFT cell regulates light transmission from the backlight assembly when
activated by the data source. By regulating the amount of light passing through the array of red, green, and blue
dots, color images are created with clarity.

2 Data Sheet EN0442EJ1V0DS00

 NL6448BC20-08

BLOCK DIAGRAM

H-driver

· · · · · ·
100 Ω
R0-R5 1920 lines
Digital
100 Ω Level
signal
G0-G5 shift
processor
100 Ω · TFT LCD panel
B0-B5 ·

480 lines
V-driver
·
H: 640 × 3 (R, G, B)
·
V: 480
·
47 Ω
CLK
100 Ω LCD timing
H sync controller
100 Ω
V sync

VCC

47 kΩ

100 Ω
DE
DPS

47 kΩ

Power LSIs (VCCi: 3.3 V)

VCC supply
circuit Drivers

GND (SG)

Frame (FG)

Data Sheet EN0442EJ1V0DS00 3

 NL6448BC20-08

(1) In case of use NEC recommended inverter

Backlight

VDDB Inverter

(Part No. 65PWB31)

BRTL
BRTH
GNDB

(2) In case of use the inverter of customers

Lamp
VH
VL

VL
VH
Lamp

Backlight

OUTLINE OF CHARACTERISTICS (at room temperature)

Display area 132.48 (H) × 99.36 (V) mm
Drive system a-Si TFT active matrix
Display colors 262144
Number of pixels 640 × 480
Pixel arrangement RGB vertical stripe
Pixel pitch 0.207 (H) × 0.207 (V) mm
Module size 178.8 (H) × 126.8 (V) × 11.0 typ. (D) mm
Weight 240 g (typ.)
Contrast ratio 250:1 (typ.)
Viewing angle (more than the contrast ratio of 10:1)
• Horizontal : 50° (typ. left side, right side)
• Vertical : 35° (typ. up side), 45° (typ. down side)
Designed viewing direction
• wider viewing angle with contrast ratio : up side (12 o’clock, reverse scan)
: down side (6 o’clock, normal scan)
• wider viewing angle without image reversal: up side (12 o’clock, normal scan)
: down side (6 o’clock, reverse scan)
Palarizer pencil-hardness 2H (min. at JIS K5400)
Color gamut 42% (typ. center to NTSC)
Response time 16 ms (typ.) “white” to “black”
2
Luminance 300 cd/m (typ.)
Signal system 6-bit digital signals for each of RGB primary colors,
Synchronous signals (Hsync, Vsyc), Dot clock (CLK)
Supply voltage 5.0 V (3.3 V) (Logic, LCD driving)
Backlight Edge light type: two fluorescent lamps (cold cathode type)
Power consumption 5.0 W (typ., at 300 cd/m2, not include inverter less)

4 Data Sheet EN0442EJ1V0DS00

 NL6448BC20-08

GENERAL SPECIFICATIONS

Item Specifications Unit

Module size 178.8 ± 0.5 (H) × 126.8 ± 0.5 (V) × 11.5 max. (D) mm

Display area 132.48 (H) × 99.36 (V) mm

Number of pixels 640 (H) × 480 (V) pixel

Dot pitch 0.069 (H) × 0.207 (V) mm

Pixel pitch 0.207 (H) × 0.207 (V) mm

Pixel arrangement RGB (Red, Green, Blue) vertical stripe −

Display colors 262144 color

Weight 260 (max.) g

ABSOLUTE MAXIMUM RATINGS

Parameter Symbol Rating Unit Remarks

Supply voltage VCC −0.3 to 6.5 V Ta = 25°C

VI − VCC < 3.0
VDD −0.3 to 6.5 V

Input voltage VI −0.3 to VCC + 0.3 V

Lamp voltage VL 1600 Vrms −

Storage temp. TST −25 to 70 °C −

Operating remp. TOP 0 to 60 °C module surface Note

Humidity RH ≤ 95% relative humidity Ta ≤ 40°C

(no condensation)
≤ 85% relative humidity 40 < Ta ≤ 50°C

Absolute humidity shall not exceed Ta > 50°C

Ta = 50°C, 85% relative humidity level.

Note measured at the display area

ELECTRICAL CHARACTERISTICS

(1) Logic, LCD driving

Ta = 25°C
Parameters Symbols Min. Typ. Max. Unit. Remarks

Supply voltage VCC 4.75 5.0 5.25 V −

(3.0) (3.3) (3.6)

Logic input “L” voltage VIL 0 − VCCi × 0.3 V CMOS level Note 2

Logic input “H” voltage VIH V C Ci × 0.7 − VCC V

−
Note 1
Supply current ICC 200 450 mA VCC = 5.0 V
(320) (600) (VCC = 3.3 V)

Notes 1. Checker flag pattern (in EIAJ ED-2522)

2. VCCi = 3.3 V : VCCi is given by DC/DC converter in the LCD module.

Data Sheet EN0442EJ1V0DS00 5

 NL6448BC20-08

(2) Backlight
Ta = 25°C
Parameters Symbols Min. Typ. Max. Unit. Remarks

Lamp current IL 2.0 5.0 6.0 mArms with one lamp

Lamp voltage VL − 400 − Vrms −

Lamp turn on voltage VS − − 720 Vrms Ta = 0°C

− − 590 Ta = 25°C

Oscillator frequency Ft 50 54 58 kHz Note

Note Recommended value of “Ft”

• Ft is within the specification.

and

• Ft = 1 × (2n – 1) th: Hsync period

4th n : a natural number (1, 2, 3, ····)
If Ft is out of the recommended value, interference between F t frequency and Hsync frequency may cause
beat on the display.

SUPPLY VOLTAGE SEQUENCE

4.75 V (3.0 V) 4.75 V (3.0 V)

VCC
0V 0 < t < 35 ms 0 < t < 35 ms

t < 150 ms

Signal VALID
0V
Power-on Power-off

*1 The supply voltage for input signals should be the same as VCC.
*2 Apply VDDB within the LCD operation period. When the backlight turns on before LCD operation or the LCD
operation turns off before the backlight turn off, the display may momentarily become white.
*3 When the power is off, please keep whole signals (Hsync, Vsync, CLK, DE, and DATA) low level or high
impedance.

6 Data Sheet EN0442EJ1V0DS00

 NL6448BC20-08

INTERFACE PIN CONNECTION

Module side connector Mating connector

CN31 ····· IL-310-T31PB-VF (No. 1 to 31) IL-310-T31S-VF
Supplier: Japan Aviation Electronics or
Industry Limited (JAE) DF9-31S-1V or DF9M-31S-1R
Supplier: HIROSE ELECTRIC CO., LTD
(1) 6-bit interface signals, power supply

Pin No. Symbols Function Pin No. Symbols Function

1 GND Ground 17 G4 Green data

2 CLK Dot clock 18 G5 Green data (MSB)

3 Hsync Horizontal synchronous 19 GND Ground

4 Vsync Vertical synchronous 20 B0 Blue data (LSB)

5 GND Ground 21 B1 Blue data

6 R0 Red data (LSB) 22 B2 Blue data

7 R1 Red data 23 B3 Blue data

8 R2 Red data 24 B4 Blue data

9 R3 Red data 25 B5 Blue data (MSB)

10 R4 Red data 26 GND Ground

11 R5 Red data (MSB) 27 DE Data enable

12 GND Ground 28 VCC Power supply

13 G0 Green data (LSB) 29 VCC Power supply

14 G1 Green data 30 N.C. Non-connection (Open)

15 G2 Green data 31 DPS Scan Direction select

16 G3 Green data LSB : Least Significant Bit

MSB: Most Significant Bit
Notes 1. VCC : All VCC terminals should be connected to VCC.
2. DPS: Normal scan is “L” or “Open”. And reverse scan is “H”.
3. During the operation, do not change the operation mode: e.g. scan direction.

Data Sheet EN0442EJ1V0DS00 7

 NL6448BC20-08

(2) Inverter
<2-1> In case of use NEC recommended inverter
• Inverter side connector 1 Mating connector 1
CN1 ··· IL-Z-6PL-SMTY IL-Z-6S-S125C3
Supplier: Japan Aviation Electronics Industry Limited (JAE)

Pin No. Symbols Function Pin No. Symbols Function

1 GNDB Backlight ground 4 VDDB Power supply

2 GNDB Backlight ground 5 BRTL Luminance control input

3 VDDB Power supply 6 BRTH Luminance control input

• Inverter side connector 2 Mating connector 2 (Lamp side)

CN2 and CN3 ··· SM02 (8.0) B-BHS-TB BHR-03VS-1
Supplier: J.S.T TRADING COMPANY, LTD.

Pin No. Symbols Function

1 VH High voltage terminal

2 N.C. Non-connection

3 GNDB Backlight ground

Notes 1. A way of luminance control by a variable resistor

Mating variable resistor : 10 kΩ ±5%

BRTL BRTH Minimum luminance (50%) : R = 0 Ω
Maximum luminance (100%) : R = 10 kΩ
R

2. A way of luminance control by a voltage

The range of input voltage between BRTH and GNDB is as follows.
Minimum luminance (50%) : 1.5 V
Maximum luminance (100%): 1.9 V

8 Data Sheet EN0442EJ1V0DS00

 NL6448BC20-08

3. Connector location

Upper side

To CN2 LCD module

or CN3
3

2 <Rear view>

1 CN31

To CN2
or CN3 1 2
<Pin arrangement 3 4
of CN2 and CN3> · ·
· ·
Lower side · ·
· ·
· ·
31 30
3
Recommended inverter
CN3 2 <Pin arrangement of CN31>

1
1
CN2
2
<Pin arrangement of CN2 and CN3>
3
CN1
4

Inverter 5
(Part No. 65PWB31)
6

<Pin arrangement of CN1>

Data Sheet EN0442EJ1V0DS00 9

 NL6448BC20-08

<2-2> In case of use the inverter of customers

• Module side connector Mating connector
CN2 and CN3: BHR-03VS-1 CN2 and CN3: SM03 (4.0) B-BHS-1-TB
Supplier: J.S.T TRADING COMPANY. LTD. Supplier: J.S.T TRADING COMPANY.LTD.

Pin No. Symbols Function

1 VH High voltage terminal (The cable color is white.)

2 N.C. non-connection

3 VL Low voltage terminal (The cable color is gray.)

Upper side

To CN2 LCD module

or CN3
3

2 <Rear view>

1 CN31

To CN2
or CN3 1 2
3 4
· ·
Lower side · ·
· ·
· ·
· ·
31 30

<Pin arrangement of CN31>

PIN DESCRIPTIONS

Symbols Functions Logic Descriptions

Vsync Vertical sync. Negative Vertical synchronous signal

Hsync Horizontal sync. Negative Horizontal synchronous signal

CLK Dot clock Negative Timing signal for display data. The video signal is
sampled at the falling edge of DOTCLK.

R0 to R5 Display data Positive 6 bits digital signals for each of RGB primary colors.
G0 to G5
B0 to B5

DE Data enable signal Positive Data enable signal

Back-porch (thb and tvb) can be changed when DE is
high. Don’t fix “DE = Low”, if not, the display will have
un-uniformity.

DPS Scan direction select − Note

VCC Power supply − +5.0 V (+3.3 V)

GND Ground − Logic ground for VCC

Note DPS: DPS changes display scan direction.

GND or Open = Normal scan
VCC = Reverse scan
See 7-8. DISPLAY POSITION about another way for reversible scan.

10 Data Sheet EN0442EJ1V0DS00

 NL6448BC20-08

DISPLAY COLORS vs. INPUT DATA SIGNALS

(1) 6-bit interface signals

Data signals (0: Low level, 1: High level)

Display colors
R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0

Basic colors Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1
Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0
Magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1
Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0
Cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

Red grayscale Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0
Dark 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0
↑
↓
Bright 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0
1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0
Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0

Green grayscale Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0
Dark 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0
↑
↓
Bright 0 0 0 0 0 0 1 1 1 1 0 1 0 0 0 0 0 0
0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0
Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0

Blue grayscale Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
↑
↓
Bright 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 1
0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0
Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1

Note Colors are developed in combination with 6 bit signal (64 steps in grayscale) of each primary red, green,
and blue color.
This process can result in up to 262144 (64 × 64 × 64) colors.

Data Sheet EN0442EJ1V0DS00 11

 NL6448BC20-08

INPUT SIGNAL TIMING

(1) Input signal specifications

Parameters Symbols Min. Typ. Max. Unit Remarks

CLK Frequency 1/tc 21.0 25.175 29.0 MHz 39.722 ns (typ.)

Duty tch/tc 0.4 0.5 0.6 − −

Rise, fall tcrf − − 10 ns −

Hsync Period th 30.0 31.778 33.6 µs 31.468 kHz (typ.)

− 800 − CLK

Display period thd − 25.422 − µs −

− 640 − CLK

Front-porch thf − 0.636 − µs −

0 16 − CLK

Pulse width thp − 3.813 − µs −

10 96 − CLK

Back-porch thb − 1.907 − µs −

5 48 − CLK

*) thp + thb 64 144 − CLK −

CLK-Hsync timing thch 12 − − ns −

Hsync-CLK timing thcs 8 − − ns −

Hsync-Vsync timing tvh 15 − − ns −

Vsync-Hsync timing tvs 15 − − ns −

Rise, fall thrf − − 10 ns −

Vsync Period tv 16.1 16.683 17.2 ms 59.94 Hz (typ.)

− 525 − H

Display period tvd − 15.253 − ms −

− 480 − H

Front-porch tvf − 0.381 − ms −

1 12 − H

Pulse width tvp − 0.063 − ms −

2 2 − H

Back-porch tvb − 0.985 − ms −

4 31 − H

*) tvp + tvb 6 33 − H −

Rise, fall − − 10 ns −

DATA CLK-DATA timing tds 8 − − ns −

R0 to R5
DATA-CLK timing tdh 12 − − ns −
G0 to G5
B0 to B5 Rise, fall tdrf − − 10 ns −

DE DE-CLK timing tes 8 − − ns −

CLK-DE timing teh 12 − − ns

Rise, fall terf − − 10 ns

Note All parameters should be kept within the specified range.

12 Data Sheet EN0442EJ1V0DS00

 NL6448BC20-08

(2) Definition of input signal timing

<Vertical>
tv

tvp

Vsync

tvb tvf

Display period Note 1

tvd

DE

<Horizontal>
th

thp

Hsync

thb thf

Display period Note 1

thd

DE

Notes 1. Display period does not exist as signals.

2. Set the total of thp + thb and tvp + tvb as the table of input signal timing, otherwise display position is
shifted to right or left side, or to up or down side.

Data Sheet EN0442EJ1V0DS00 13

 NL6448BC20-08

tc

tch

VIH
CLK Vcci × 0.5
VIL
tcrf tcrf

tds tdh
DATA INVALID INVALID
(R0 to R5) VIH
(G0 to G5) Vcci × 0.5
(B0 to B5) VIL
tdrf tdrf

teh tes teh tes

VIH
DE Vcci × 0.5
VIL
terf terf

CLK Vcci × 0.5

thch thcs

VIH
Hsync Vcci × 0.5
VIL
thrf

Hsync Vcci × 0.5

tvh tvs

VIH
Vsync Vcci × 0.5
VIL
tvrf

VIH = VCCi × 0.7 (min.)

VIL = VCCi × 0.3 (max.)

VCCi = 3.3 V: VCCi is given by DC/DC converter in the LCD module.

14 Data Sheet EN0442EJ1V0DS00

 NL6448BC20-08

(3) Input signal timing chart

Vsync

1H

tvp tvb 480H (fixed) tvf

Hsync

1 2 3 1

DE

R0 to R5
G0 to G5
B0 to B5
INVALID D (X, 0) D (X, Y) D (X, 479) INVALID
(Note: X = 0 to 639)

DE

R0 to R5
G0 to G5
B0 to B5
INVALID D (0, Y) D (1, Y) D (X, Y) D (638, Y) D (639, Y) INVALID

Hcync

1CLK

thp thb 640CLK (fixed) thf

CLK

1 2 1

DE

R0 to R5
G0 to G5
B0 to B5
INVALID D (0, Y) D (1, Y) D (639, Y) INVALID
(Note: Y = 0 to 479)

Data Sheet EN0442EJ1V0DS00 15

 NL6448BC20-08

DISPLAY POSITION

Normal scan: DPS = “L” (factory set)

D (0, 0) D (1, 0) D (X, 0) D (638, 0) D (639, 0)

D (0, 1) D (1, 1) D (X, 1) D (638, 1) D (639, 1)

D (0, Y) D (1, Y) D (X, Y) D (638, Y) D (639, Y)

D (0, 478) D (1, 478) D (X, 478) D (638, 478) D (639, 478)

D (0, 479) D (1, 479) D (X, 479) D (638, 479) D (639, 479)

Reverse scan: DPS = “H”

D (639, 479) D (638, 479) D (X, 479) D (1, 479) D (0, 479)

D (639, 478) D (638, 478) D (X, 478) D (1, 478) D (0, 478)

D (639, Y) D (638, Y) D (X, Y) D (1, Y) D (0, Y)

D (639, 1) D (638, 1) D (X, 1) D (1, 1) D (0, 1)

D (639, 0) D (638, 0) D (X, 0) D (1, 0) D (0, 0)

Note Below drawings show relations between the scan direction and the viewing direction.

Normal scan Reverse scan

D (0, 0) D (639, 0)
D (0, 0) D (639, 0) CN
31

CN
31 D (0, 479) D (639, 479)
D (0, 479) D (639, 479)

16 Data Sheet EN0442EJ1V0DS00

 NL6448BC20-08

OPTICAL CHARACTERISTICS
Ta = 25°C Note 1
Parameters Symbols Conditions Min. Typ. Max. Unit Remarks

Contrast ratio CR Note 2 150 250 − − Note 3

Luminance Lu Note 2 250 300 − cd/m

2
Note 4

Luminance uniformity − max./min. − − 1.25 − Note 5

Reference data

Parameters Symbols Conditions Min. Typ. Max. Unit Remarks

Response time t on White to black − 16 40 ms Note 6

t off Black to white − 55 90 ms

Color gamut C at center, to NTSC 35 42 − % −

Viewing Horizontal θx+ CR > 10, θ y = ±0° 45 50 − deg. Note 7

angle range
θx− CR > 10, θ y = ±0° 45 50 − deg.

Vertical θy+ CR > 10, θ x = ±0° 30 35 − deg.

θy− CR > 10, θ x = ±0° 40 45 − deg.

Notes 1. VCC = 5.0 V, IL = 5.0 mA rms, with NEC recommended inverter (Part No.65PWB31).
2. Viewing angle: θ x = ±0°, θ y = ±0°, At center.
Best contrast angle: θ x = ±0°, θ y = −10°, At center.
3. The contrast ratio is calculated by using the following formula.

Luminance with all pixels in “white”

Contrast ratio (CR) =
Luminance with all pixels in “black”

The Luminance is measured in darkroom.

4. The luminance is measured after 20 minutes from the module works, with all pixels in “white”. Typical
value is measured after luminance saturation.

1°
Photodetector (TOPCON BM-5A)

50 cm
LCD MODULE

Data Sheet EN0442EJ1V0DS00 17

 NL6448BC20-08

5. The luminance uniformity is calculated by using following formula.

Maximum luminance
Luminance uniformity =
Minimum luminance

The luminance is measured at near the five points shown below.

Column (160) (320) (480)

Line

1 4 (120)

3 (240)

2 5 (360)

6. Definition of response time is as follows.

Photodetector output signal is measured when the Luminance changes “white” to “black”. Response
time is the time between 10% and 100% of the photodetector output amplitude.

100% White

Display color
90%
Luminance
range

10% Black
0%
ton toff Time

7. Definitions of viewing angle are as follows.

Perpendicular

12 o’clock
θ x–
Left θ y+
Upper
θ x+

θ y–

Lower
Right

18 Data Sheet EN0442EJ1V0DS00

 NL6448BC20-08

RELIABILITY TEST

No. Test items Test conditions Judgement

1. High temperature/humidity 50 ± 2°C, 85% relative humidity Note 1

operation 240 hours
Display data is black.

2. High temperature (operation) 60 ± 3°C Note 1

240 hours
Display data is black.

3. Heat cycle (operation) <1> 0°C ± 3°C ··· 1 hour Note 1

55°C ± 3°C ··· 1 hour
<2> 50 cycles, 4 hours/cycle
<3> Display data is black.

4. Thermal shock (non-operation) <1> –25°C ± 3°C ··· 30 minutes Note 1

70°C ± 3°C ··· 30 minutes
<2> 100 cycles
<3> Temperature transition time within 5 minutes

5. Vibration (non-operation) <1> 5 - 100 Hz, 2G Note 1

1 minute/cycle, Note 2
X, Y, Z direction
<2> 120 times each direction

6. Mechanical shock (non- <1> 55 G, 11 ms Note 1

operation) X, Y, Z direction Note 2
<2> 5 times each direction

7. ESD (operation) 150 pF, 150 Ω, ±10 kV Note 1

9 places on a panel Note 3
10 times each place at one-second intervals

8. Dust (operation) 15 kinds of dust (JIS Z 8901) Note 1

Hourly 15 seconds stir, 8 times repeat

Notes 1. Display function is checked by the same condition as LCD module out-going inspection.
2. Physical damage.
3. Discharge points are shown in the figure.

Data Sheet EN0442EJ1V0DS00 19

 NL6448BC20-08

GENERAL CAUTIONS
Next figures and sentence are very important, please understand these contents as follows.

This figure is a mark that you will get hurt and/or the module will have damages when you make
CAUTION a mistake to operate.

This figure is a mark that you will get an electric shock when you make a mistake to operate.

This figure is a mark that you will get hurt when you make a mistake to operate

CAUTION

(1) Caution when taking out the module

<1> Pick the pouch only, when taking out the module from a carrier box.

(2) Cautions for handling the module

<1> As the electrostatic discharges may break the LCD module, handle the LCD module with care against
electrostatic discharges.
<2> As the LCD panel and backlight element are made from fragile glass material, impulse and
pressure to the LCD module should be avoided.
<3> As the surface of polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for
cleaning.
<4> Do not pull the interface connectors in or out while the LCD module is operating.
<5> Put the module display side down on a flat horizontal plane.
<6> Handle connectors and cables with care.
<7> When the module is operating, do not lose CLK, Hsync, or Vsync signal. If any one or more of these
signals is lost, the LCD panel would be damaged.
<8> The torque for mounting screw should never exceed 0.20 N·m (2 kgf·cm).

(3) Cautions for the atmosphere

<1> Dew drop atmosphere must be avoided.
<2> Do not store and/or operate the LCD module in high temperature and/or high humidity atmosphere.
Storage in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere
is recommended.
<3> This module uses cold cathod fluorescent lamps. Therefore, the life time of lamp becomes short
conspicuously at low temperature.
<4> Do not operate the LCD module in high magnetic field.

(4) Caution for the module characteristics

<1> Do not apply any fixed patterns data signal to the LCD module at product aging. Applying fixed pattern for
a long time may cause image sticking.
<2> This module has the retardation film which may cause the variation of the color hue in the different viewing
angles. The ununiformity may appear on the screen under the high temperature operation.

20 Data Sheet EN0442EJ1V0DS00

 NL6448BC20-08

(5) Other cautions

<1> Do not disassemble and/or reassemble LCD module.
<2> Do not readjust variable resistors nor switches etc.
<3> When returning the module for repair or etc, pack the module not to be broken. We recommend the
original shipping packages.

Liquid Crystal Display has the following specific characteristics. There are not defects nor malfunctions.
The display condition of the LCD module may be affected by the ambient temperature.
The LCD module uses cold cathode tube for backlighting. Optical characteristics, like luminance or
uniformity, will change during time.
Uneven brightness and/or small spots may be noticed depending on different display patterns.

Data Sheet EN0442EJ1V0DS00 21

 NL6448BC20-08

OUTLINE DRAWING/FRONT SIDE (Unit in mm)

7.6±0.5
3.3±0.3

3.3±0.3
2.5±0.3

2.5±0.3
126.8±0.5
98±0.3
(49) (14.4)

K1028B2015035 98.12.18/
ES8C10004 MADE IN JAPAN
NL6448BC20-08

MODULE CENTER
178.8±0.5
172±0.3

172±0.3
ACTIVE AREA
(1)

CENTER

(86)
(86)
(3.4)

(48)
11.5 MAX.

4- φ 2.8 96±0.3 (15.4)

2.5±0.3
3.3±0.3

MOUNTING HOLE
(9.3)

FRONT VIEW
(7.8)
7.6±0.5
3.3±0.3
2.5±0.3

(10.1)
(46.95)

22 Data Sheet EN0442EJ1V0DS00

 NL6448BC20-08

OUTLINE DRAWING/REAR SIDE (Unit in mm)

I/F CONNECTOR
(66.4) IL-310-T31P-VF (JAE)
(20.4) (20.4)

(9.2)

(9.2)
(169)

K 1 0 2 8 B 2 0 1 5 0 3 5

DISPOSAL
OR REGULATIONS FOR ITS
FOLLOW LOCAL ORDINANCES
FLOURESCENT LAMPS. PLEASE
PANEL CONTAINS COLD CATHODE
THE TFT COLOR LCD
O
Name 65BLM04
Pal No.

POWER BEFORE SERVICE.

DISCONNECT THE ELECTRIC
RISK OF ELECTRIC SHOCK.
∗∗∗−∗

NION VOLTEGE
CAUTION
(9.75)

(9.7)

(4.35) (4.35)
(17.95) (17.95)
112±10

112±10

REAR VIEW

I/F CONNECTOR I/F CONNECTOR

BHR-03VS-1 (JST) BHR-03VS-1 (JST)

Notes 1. Not shown tolerances of the dimensions are ±0.5 mm.

2. The value in parenthese are for reference.

Data Sheet EN0442EJ1V0DS00 23

 NL6448BC20-08

No part of this document may be copied or reproduced in any form or by any means without the prior written
consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in
this document.
NEC Corporation does not assume any liability for infringement of patents. Copyrights or other intellectual
property rights of third parties by or arising from use of a device described herein or any other liability arising from
use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or
other intellectual property rights of NEC Corporation or others.
While NEC Corporation has been making continuous effort to enhance the reliability of its Electronic
Components, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to
persons or property arising from a defect in an NEC Electronic Components, customers must incorporate
sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features.
NEC devices are classified into the following three quality grades:
“Standard”, “Special”, and “Specific”. The Specific quality grade applies only to devices developed based on a
customer designated “quality assurance program” for a specific application. The recommended applications of a
device depend on its quality grade, as indicated below. Customers must check the quality grade of each device
before using it in a particular application.
Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio
and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial
robots
Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster
systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support)
Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support
systems or medical equipment for life support, etc.
The quality grade of NEC devices is “Standard” unless otherwise specified in NEC’s Data Sheets or Data Books.
If customers intend to use NEC devices for applications other than those specified for Standard quality grade,
DATA SHEET
they should contact an NEC sales representative in advance.
Anti-radioactive design is not implemented in this product.