Converting Porsche 928 Interior Lighting to

LEDs
Ed Scherer <[email protected]>

May 13, 2013

Revision 0.7 (Incomplete Draft)

1
 Converting Porsche 928 Interior Lighting to LEDs

Introduction ................................................................................................................................................................4
Scope and Limitations ............................................................................................................................................4
Requirements .........................................................................................................................................................4
Caveats ...................................................................................................................................................................4
Terminology............................................................................................................................................................4
How to View Photos at Higher Resolution .............................................................................................................5
Warnings.................................................................................................................................................................5
Credits.....................................................................................................................................................................5
Parts, Tools, and Techniques ......................................................................................................................................6
Necessary (or Just Useful) Items ............................................................................................................................6
Working with LEDs..................................................................................................................................................6
Instrument Cluster......................................................................................................................................................9
Instrument Cluster Lamp Summary........................................................................................................................9
Tools for Use Working With the Instrument Cluster ........................................................................................... 10
Instrument Cluster Removal................................................................................................................................ 10
Instrument Cluster Disassembly .......................................................................................................................... 13
Instrument Cluster Lamp Replacement............................................................................................................... 17
Instrument Cluster Reinstallation........................................................................................................................ 28
Additional Labeling on PC Board ......................................................................................................................... 30
Pod Switches............................................................................................................................................................ 31
Pod Switch Lamp Summary ................................................................................................................................. 31
Normal Pod Switch Backlighting Behavior .......................................................................................................... 31
Tools for Use Working With the Large Cylindrical Pod Switches ........................................................................ 32
Large Cylindrical Pod Switch Removal ................................................................................................................. 32
Replacing the Original Incandescent Bulbs with LED Bulbs................................................................................. 33
Adding Resistors to Set Maximum “Dim” Level .................................................................................................. 34
Intensive Windshield Cleaning Switch................................................................................................................. 35
Center Console Switches and Instrumentation ....................................................................................................... 37
Automatic Climate Control .................................................................................................................................. 37
Central Door Locking Button ............................................................................................................................... 37
Clock .................................................................................................................................................................... 37
Cigarette Lighter / Ashtray .................................................................................................................................. 37

2
 Converting Porsche 928 Interior Lighting to LEDs

Courtesy Lighting ..................................................................................................................................................... 37

Footwell Lights in Lower Door Panels ................................................................................................................. 37
Light in Headlining Near Front Visors .................................................................................................................. 37
Light in Headlining Near Rear Visors ................................................................................................................... 37
Luggage Compartment Light ............................................................................................................................... 37
Glove Box Light .................................................................................................................................................... 37
Central Electric Panel Area Light ......................................................................................................................... 37
Restoring Dimming Functionality ............................................................................................................................ 38
Part Summary .......................................................................................................................................................... 39
Order Extras! ....................................................................................................................................................... 39
Instrument Cluster............................................................................................................................................... 39
Pod Switches........................................................................................................................................................ 40
Center Console Switches and Instrumentation ................................................................................................... 41
Courtesy Lighting ................................................................................................................................................. 41

3
 Converting Porsche 928 Interior Lighting to LEDs

Introduction
This document is intended to provide guidance to those who would like to upgrade their Porsche 928 to use
LEDs rather than incandescent lamps for interior lighting. While some of the interior lighting (such as the
courtesy lights) are quite simple to upgrade to LEDs, other items such as the instrument cluster and central
console (climate control head, etc.) are quite a bit more challenging.

Scope and Limitations

This document is based on my experiences of upgrading a 1990 Porsche 928 S4. It is likely that this guide will
apply to 1989 and later 928s; earlier models, however, had significantly different instrument clusters. Models
prior to 1987 are even more different and even less of this guide will apply.

Requirements
As I was carrying out my interior lighting upgrades from incandescent lighting to LED lighting, I had the following
requirements (or at least preferences):

 Replace every incandescent bulb with an LED bulb.

 Increase overall brightness of instrumentation lighting (both backlighting and indicators).

 For any socketed bulb, find replacement LED lamps with identical bases if possible (i.e., no filing or other
modification of bulb base or socket).

 Attempt to achieve uniform brightness of indicators, i.e., don’t have any indicators arbitrarily brighter
than others (e.g., the central locking button always struck me as being way too bright when fully
illuminated relative to the other indicators).

 Retain functionality of the instrument illumination control using the original rheostat.

Caveats
In a few cases, results were short of what I would consider ideal. These were—in my opinion—acceptable, but
still noteworthy. Rather than listing those items here, I have noted them in sidebars.

Terminology
“Owner’s Manual” terminology is used when appropriate. For example, the speedometer and tachometer
(among many other instruments and lights) are part of the instrument cluster, which also contains the park
brake warning light, the air bag warning light, the high beam indicator light, etc.

The S.I. system of units is used.

4
 Converting Porsche 928 Interior Lighting to LEDs

How to View Photos at Higher Resolution

If you are viewing this document using Adobe Reader (or any other PDF viewer that supports links), the photos
in this document are links; if you click a photo, your viewer application should take you to a substantially higher-
resolution image on Picasa Web.

Note that when viewing a photo in a web browser, many web browsers (such as Microsoft Internet Explorer) will
scale the photo so it will fit within the viewable area of the browser window. You can typically click the image to
re-expand it to its full resolution, and then you can scroll around in the image using the browser’s horizontal and
vertical scroll bars.

Warnings
Always disconnect the car’s battery ground strap before performing significant work on the car’s
electrical system unless you are absolutely sure that the circuit you are working on is not live (e.g.,
you’re sure that you’ve removed a fuse that provides power to the circuit). This isn’t necessary for minor
items (such as pulling the knob off a pod switch and replacing the bulb). But for complex devices such as
the instrument cluster, there are so many signals from so many sources that it is not wise to attempt to
work on it (or disconnect/connect it) “hot.”

[more warnings TBA]

Credits
I would like to acknowledge the trailblazing work related to interior lighting of three people:

 Keith Widom (Rennlist handle “928ntslow”), whose “Interior LED Changeover (uhm...Looooong)” thread
on the Rennlist 928 Forum provided the inspiration for diving into the instrument cluster and some of
the other lighting. In fact, I regard my write-up as a more comprehensive and updated version of Keith’s
write-up.

 (Rennlist handle) “Schocki”, whose “15 minute instrument pod removal update and instrument light
bulbs for an OK price” thread on the Rennlist 928 Forum provided key information on how to remove
the instrument cluster without removing the steering wheel. Those who doubt that you can remove the
instrument cluster in fifteen minutes… well, (with the knee protector trim already removed) I timed
myself and got mine out in six minutes. Once you’ve done it at least once, it’s really easy. Getting in back
in takes a little longer (at least it does for me ).

 “Wojtek”, whose “My 1987 Porsche 928 S4, 5 speed: Instruments Illumination” provided some very
good ideas about instrument illumination, particularly related to the climate control head (I wound up
doing something like what he did for backlighting the fan speed control knob).

5
 Converting Porsche 928 Interior Lighting to LEDs

Parts, Tools, and Techniques

Necessary (or Just Useful) Items
 soldering iron suitable for use on small-gauge wires and PC boards (you might find that you’ll want a flat
tip for some tasks and a conical tip for other tasks)

 solder

 solder sucker and/or wick for de-soldering

 clip-on heat sink (for dissipating heat from heat-sensitive components

when soldering)

 wire cutters

 needle-nose pliers

 assortment of heat-shrinkable tubing

 bench power supply

 multimeter

 test leads terminated with alligator clips, test clips (I really like the little “hook” style), banana plugs;
various terminations are used for attaching to power supply, multimeter, circuit under test/being
powered, etc.

Working with LEDs

LED Types
There are two main types of LEDs you will be working with in the applications covered by this document:

 12 V LED lamps: these are one or more discrete LEDs (see next item) packaged along with a diode
(sometimes four diodes in a bridge rectifier configuration, which allows the bulb to be non-
polarized, i.e., works when inserted into the socket “either way”) and current limiting
resistor wired in series such that the LED(s) are protected against reverse voltage (by the
diode) and such that their drive currents are regulated by the resistor so they are operating
with safe power dissipation when a +12 V voltage is applied across the lamps’ terminals.
These LED lamps are generally easy to work with and unlikely to be damaged as long as you don’t
exceed 14 V when powering them.

 Discrete LEDs (also known as component LEDs): these are just “raw LEDs” that rely on external circuitry
to limit their drive current. They should not be reverse biased, i.e., they should not have

6
 Converting Porsche 928 Interior Lighting to LEDs

a higher voltage at their cathode than their anode. Discrete LEDs should be used with care, as they can
be easily destroyed in two ways: reverse biasing them or exceeding their rated maximum drive current.

Applying current from a typical power supply or battery directly to a discrete LED without using a
current-limiting resistor in series with the LED is likely to destroy the LED.

LED Polarity
 With the exception of non-polarized LED bulbs (which are fairly uncommon, but becoming more
common for festoon bulbs), it is important that you get the polarity correct on LED
bulbs when inserting them into a circuit. LEDs have an anode (“positive side”) and
cathode (“negative side”). In an automotive application, the anode is typically
connected to some positive voltage (usually a +12 V source or some other smaller positive voltage) and
the cathode is typically connected to ground. Some LED bulbs are diode-protected so that if you insert
them with reversed polarity, it will do no harm, but (again, with the exception of non-polarized LED
bulbs) a diode-protected LED bulb inserted with inverted polarity will not light.

 The polarity on some LED bulbs that have internal reverse voltage protection is often not marked. It is
best to bench test your LED bulbs and, while you’re at it, mark the polarity. I mark the cathode side (that
will connect to the ground/low/negative side of the PC board) with a black marker. Likewise, the sockets
for the bulbs—since they were typically intended for use with incandescent bulbs (non-polarized)—
should be marked; a black mark on the ground side should suffice.

 On the most common discrete LEDs, the cylindrical/dome-shaped 3 mm or 5 mm diameter ones, the
cathode is indicated by the flat side of the flange on the plastic package as well as the shorter of the two
leads.

 A discrete LED will likely be destroyed almost On-Line LED Current-Limiting

instantaneously if you reverse bias it (i.e., apply a higher Resistor Calculators
voltage to its cathode than its anode). Actually, you can get There are on-line calculators that, given
away with some reverse bias (as long as you don’t exceed a few of the parameters of an LED, will
provide you with the minimum
the LEDs reverse bias breakdown voltage), but it’s best to
acceptable current-limiting resistor.
just avoid ever applying reverse polarity when working
with discrete LEDs. For example, the “LED Calculator” at
http://ledcalculator.net/ given the

Choosing Current-Limiting Resistors for values from Example #1 (see main text
on left) provides the following
Discrete LEDs schematic:
If you are using discrete LEDs to replace incandescent bulbs (i.e., in
the absence of existing LED driving circuitry), you will
need to add a current-limiting resistor (and optionally,
a reverse polarity protection diode).

To determine the resistance needed, consult the specifications of the LED; look for the “continuous forward
current” parameter. Then, given the voltage (14 V if you want to be conservative, knowing that in automotive

7
 Converting Porsche 928 Interior Lighting to LEDs

applications, the voltage is often higher than 12 V and sometimes as high as 14 V), apply Ohm’s law: V = I × R,
i.e., voltage equals current times resistance. Use a resistor of at least the calculated value (the higher the
resistance, the less current will flow through the LED, making it dimmer, but also making it run cooler and last
longer).

Example #1: given a LED with continuous forward current of 50 mA, then R = 14 V ÷ 0.05 A = 280 Ω. So… you
would use a resistor of at least 280 Ω. In this case, I’d experiment with resistors certainly no less than 280 Ω, but
perhaps as high as 1.5 kΩ, choosing one that provides an acceptable light intensity (remembering that a higher
resistance means less current, less heat, and longer LED lifetime).

5%, ¼ W or ½ W carbon film resistors are usually acceptable for most discrete LED current limiting applications.
To determine whether to use a ¼ W or ½ W resistor, you can check how much power the resistor will be
dissipating using P = I × V, i.e., power equals current times voltage (actually, the LED dissipates some of the
power, too, but we can be conservative and ignore that and assume that the resistor dissipates all the power).
Note that you can substitute a ½ W resistor where a ¼ W resistor would suffice, but not (in general) vice-versa.

Example #2: Let’s assume a 14 V voltage source and a 1 kΩ resistor wired in series with an LED. The resistor
would dissipate no more than P = I × V = (V ÷ R) × V = V2 ÷ R = (14 V)2 ÷ 1000 Ω = 0.196 W. Since this is less than
0.25 W, a ¼ W resistor would suffice.

5%, ¼ W and 5%, ½ W carbon film resistors in a wide range of resistances are readily available from both on-line
sources as well as local sources. Radio Shack carries a wide variety.

Selecting the Best LED Color

With few exceptions, it’s best to choose an LED color that is well matched to whatever color filter is in front of it.

For example, the turn signal indictor was originally a “white” incandescent bulb behind a green filter to make
the indicator “green”. Use a green LED for this application.

Whereas incandescent bulbs emit light with a fairly wide range of frequencies in the color spectrum (generally
rather “yellowish white”), LEDs emit light at a very specific frequency; they emit a more “pure” color, e.g., “pure
green.” Using a white LED behind a colored filter generally won’t give results as appealing (the color won’t be as
saturated) as putting the same color LED behind the filter as the filter color.

In a few cases (such as the automatic-transmission-equipped car’s “selector lever position indicator”), a
compromise must be made, as the same lamp shines through multiple filter colors (white and red or white and
green); a white LED is appropriate in such a case, but the result will appear somewhat washed out.

8
 Converting Porsche 928 Interior Lighting to LEDs

Instrument Cluster
Instrument Cluster Lamp Summary
Main Gauge Backlighting
Bulb Socket twist-lock, with contacts for W2.1x9.5d base bulb
Original Bulb Type W3W-12V with T3-1/4 glass with base W2.1x9.5d
(10 mm diameter, 26 mm long wedge base; same
base as #168 and #194)
Recommended LED Replacement Bulb Type Super Bright LEDs WLED-WHP5
Notes  Retain twist-lock base; just replace bulb.
 Absolute maximum size bulb that will fit is
12.3 mm diameter, 30 mm long (note that a
Super Bright LEDs WLED-WHP9-T will not fit).

Information System Display Backlighting

Bulb Socket twist-lock integrated with bulb (not designed to be
separated)
Original Bulb Type [TBD] with B8.4d twist base
Recommended LED Replacement Bulb Type  Super Bright LEDs B8.4D-AHP (amber) for the
upper four “LCD white” lamp positions
 Super Bright LEDs B8.4D-RHP (red) for the lower
four “LCD red” lamp positions
Notes Order extra LED bulbs and bench test to obtain sets
of four LED bulbs with good color and brightness
match (variations can be visible).

Indicator and Warning Lights

Bulb Socket twist-lock integrated with bulb (not designed to be
separated)
Original Bulb Type W1.5W-12V with T1-3/4 glass with base W2.1x4.9d
or B8.4d twist base (all the originally yellow-base
bulbs); W1.2W-12V with T1-3/4 glass with base
W2.1x4.9d or B8.4d twist base (all the originally
blue-base bulbs)
Recommended LED Replacement Bulb Type Super Bright LEDs B8.4D-xHP for the A/T selector
lever position indicators; B8.4D-x for all other
indicator and warning lights (where x is: R=red,
A=amber, W=white, G=green, B=blue)
Notes

9
 Converting Porsche 928 Interior Lighting to LEDs

Tools for Use Working With the

Instrument Cluster
A ¼ inch and/or 6 mm socket make excellent tools for
removing the B8.4D twist lock bulb bases. You can use a
flat-tip screwdriver in the slot, but the plastic base is rather
soft and tends to deform fairly easily.

“Vice Grips” (or equivalent) are useful for adjusting the

electrical contacts on the B8.4d bulbs.

A permanent black marker (Sharpie or equivalent) is

appropriate for marking polarities of LED bulbs and the
bulb positions on the PC board.

Instrument Cluster Removal

As the instrument cluster has four connectors with
numerous signals, I’d strongly recommend disconnecting
the battery (and not just trying to pull a fuse or two) when
removing the instrument cluster. Figure 1: Optimal tool for B8.4d bulb removal and
insertion
To remove the instrument cluster, follow the instructions at “15
minute instrument pod removal update and instrument light bulbs for an OK price”
(http://forums.rennlist.com/rennforums/928-forum/372301-15-minute-instrument-pod-removal-update-and-
instrument-light-bulbs-for-an-ok-price.html).

To remove the instrument pod, you will first need to remove (using a 5 mm Allen wrench) five socket head cap
screws, as shown in Figure 2.

10
 Converting Porsche 928 Interior Lighting to LEDs

Figure 2: Looking up at the bottom of the instrument pod and the five screws that secure it

You might find that disconnecting the four cables to the instrument cluster is a little challenging if you haven’t
done it before. Be very careful when unlocking the four connectors. The two little locking levers on each
connector are fairly strong, but you can break them if you don't understand how they work. Study the next
photo to assist in your understanding of how the locking levers function.

11
 Converting Porsche 928 Interior Lighting to LEDs

When working with these connectors:

 Move the locking levers slightly away (perpendicular from what appears to be their main direction of
travel) from the connector (bend them a little) to allow them to move. This is necessary because the
there are little slots on the connector and little "pins" on the locking levers that lock them into position
either fully closed or fully open.

 Operate both of the levers at the same time if you can; you probably cannot fully unlock one lever while
the other one is still locked (this is because as you move the levers to unlock, it also pushes the
connector away from the PC board, but it can't do this if the other lever is still locked and if you're not
careful and try to force it, you'll likely break the locking lever).

 Consider improving the labeling, since it is likely you’ll be plugging/unplugging them more than once and
you’ll want to be confident you’re working with the right connectors (mine had hand-written labels on
the connector, but the corresponding labels on the cluster itself were black-on-black and very hard to
see). See photos below for improved labeling.

12
 Converting Porsche 928 Interior Lighting to LEDs

Instrument Cluster Disassembly

To get to the instrument backlighting bulbs, information display backlighting bulbs, and various indicator and
warning bulbs, you will first need to separate the rear-most black part of the cluster from the white
intermediate part. To do this, rotate each of the four black knobs (see arrows in photo below) on the back of the
cluster 180° counter-(anti-)clockwise. You can see the “180°” label near each one of those knobs if you look
carefully. Note that these knobs may be difficult to turn if they haven’t been operated for some time; mine
were, so I lubricated them with some light, general-purpose oil after I got the back off so they’d subsequently be
easier to operate.

13
 Converting Porsche 928 Interior Lighting to LEDs

This unlocks the black rear part; you can then open it up like a door:

If you open them up all the way (about 90°) as shown in the above photo, the two pieces will completely
separate at the hinge when you move the white half up and the black half down.

At this point, you can familiarize yourself with the main PC board for the instrument backlighting and
indicator/warning lamps.

14
 Converting Porsche 928 Interior Lighting to LEDs

What you’ll see (mostly nicely labeled):

 eight screws holding the PC board to the white plastic enclosure;

 twenty-one silver sockets with containing pins; these are the electrical connections for the various
analog gauges (they’ll come unplugged if/when the PC board is pried off);

 four backlighting bulbs for the analog gauges (brown twist-lock bases) (labeled “CLUSTER
ILLUMINATION”); and

 lots of other bulbs in B8.4d twist-lock bases; the lower eight yellow ones are for the LCD information
display backlighting (labeled “LCD white” and “LCD red”); the rest are for various indicator and warning
lamps and are all nicely labeled.

If you were just replacing a small number of bulbs with identical incandescent bulbs, you could probably just do
that now, but as you will be doing more substantial modifications, you should remove the eight screws and
carefully pull/pry off the PC board. With the eight screws removed, the only things holding the PC board are the
analog gauge connectors; they’ll separate as you pry/lift the PC board.

Once you’ve separated them, you’ll be left with this:

15
 Converting Porsche 928 Interior Lighting to LEDs

and this:

You’ll probably get all excited and flip the PC board over so you can see all the bulbs:

At this point, you’ve got access to all the parts you’ll need to replace and work on for the LED upgrade of the
cluster.

16
 Converting Porsche 928 Interior Lighting to LEDs

Instrument Cluster Lamp Replacement

Beveling Holes in PC Board for B8.4d Bulbs
If you use the recommended B8.4d bulbs, you may find that they are a very
tight fit into the instrument cluster PC board. This is especially true for the
regular (B8.4-X, non-SMD) bulbs that are pictured in Figure 3; the B8.4-XHP
(SMD high-intensity) do not seem to suffer from this problem as much. Note
that the plastic base for the bulb is spread out a bit at the top; this makes it
a little larger than the hole in the instrument cluster PC board. This slight
size mismatch along with the sharp edge of the hole in the PC board makes
it difficult if not impossible to insert the bulb. Also, the metal contacts may
not fit through the “ears”
in the holes; the next
section discusses how to
Figure 3: B8.4-XHP bulb; note base address that problem.
spread causing increased diameter near
top of base You can try squeezing the
plastic base near the top of the base with pliers to try to
make it fit, but it will likely still be difficult to insert.

Beveling the holes in the instrument cluster PC board solves

the problem.

You can either use a round file, as shown in Figure 4, or a

Dremel with an appropriate grinding stone (e.g., Dremel
#941). A hole beveled as shown in Figure 5 will readily accept
a B8.4d (like the one shown in Figure 3).

Figure 4: Using a round file to bevel the hole for a B8.4d

bulb

Figure 5: Unmodified (left) vs. beveled (right) bulb hole

17
 Converting Porsche 928 Interior Lighting to LEDs

Dealing with Twist-Lock Contact Shape and Unreliability

Refer to the photo of the B8.4d bulb in Figure 3 and note that there are metal electrical contacts. The upper part
(the part nearer the top of the photo) is the part that will actually make electrical contact with the copper trace
on the PC board. There are two of these (the one visible in the photo and the one directly across from it on the
back that you can’t see in the photo).

Two characteristics of these contacts are very important and may

need adjustment: The Mysterious CHECK
ENGINE and CAT Warnings
 The curvature and width of the upper contacts: the upper Did you notice that there are two bulb
contact is bent into a “V” shape to allow it ride over the positions labeled CHECK ENGINE and
back edge of the “ear” part of the hole in the PC board and CAT that weren’t filled in with bulbs?
then make contact with the copper trace on the PC board.
It’s not clear why these were unused,
However, if it is not bent enough, it will not pass through but I chose to put LED lamps in these
the ear part of the holes. Adjust as needed by bending into positions.
more of a “V” shape. “Vice Grip” style pliers can be a good
And… interestingly enough, they turn
tool for this, as they can be adjusted so they won’t over- on during the “lamp check” period
compress the contact. when the ignition is first switched on.

 The spacing between the upper and lower part of each Whether or not they’ll ever actually
contact: The spacing between the upper and lower parts of illuminate to warn about anything, I
don’t yet know.
each electrical contact must be slightly less than the
thickness of the PC board. If this spacing is too small, the
contact will not turn after you’ve inserted the bulb in the hole in the PC board. If this spacing is too
large, the contact will not make electrical contact with the copper trace on the PC board. Most of the
bulbs come with the contacts spaced properly, but they bend easily, and the spacing can change when
you insert the bulb if everything doesn’t line up just right. Adjust with pliers as necessary.

Marking Polarity on the B8.4d LED Bulbs

The B8.4d LED bulbs are polarized; they will only light if inserted with their anode connected to the “positive”
contact on the PC board and their cathode connected to the “negative” contact on the PC board.

To assure that all bulbs are inserted into the PC board with correct polarity (especially considering that you may
be removing them and reinserting them or replacement bulbs for a variety of reasons (testing reveals contact
problems, failed bulbs, etc.), it is wise to mark them with their polarity since, unfortunately, this isn’t done by
the manufacturer.

You can determine polarity with a diode tester (a feature sometimes found on digital multimeters) or by just
applying a voltage (from a bench power supply or just a 9 V rectangular battery).

Once you have determined polarity, mark the cathode (negative) side with a black mark.

18
 Converting Porsche 928 Interior Lighting to LEDs

Deciding on a Color Scheme for the A/T Gear

Indicator Bulbs
Most of the photos included in this document show the gear
indicator bulbs all using white B8.4d LED bulbs. An alternative
choice you may want to consider is shown in Figure 7: green bulbs
for ‘2’, ‘3’, and ‘D’, white for ‘N’, yellow for ‘R’, and red for ‘P’.

Installing the B8.4d LED Bulbs

Figure 21 shows the polarities of the holes for each of the bulb
positions (holes for the twist-lock bulbs) on the PC board.

Insert each bulb through the hole such that when you twist 90°,
the polarities will be correct, i.e., that your black mark on the LED
will match up with the black marks on the PC board as shown in Figure 6: Alternative A/T bulb color scheme
Figure 21. You may find that a socket screwdriver is the best tool:
it can be turned and jiggled gently to work the bulb through the hole and then twist 90° to seat it.

Installing the Four #168/#194-Style Backlighting Bulbs

The four main analog gauge backlighting bulbs are also twist-lock bulbs, but they are easily removable from their
brown plastic bases. After removing the original bulbs, you can just insert the replacement LED bulbs into the
original twist-lock bases.

While you may want to insert the new LED bulbs along with their twist-lock bases into the instrument cluster PC
board and test them, you may find that it is best to temporarily remove them prior to screwing the PC board
back into the instrument cluster—the LED bulbs are big enough where it is difficult to insert the PC board into
the rest of the instrument cluster assembly with the four main backlighting LED bulbs installed. When the PC
board is screwed into position in the instrument cluster assembly, you can then easily install each of the four
bulbs, jiggling them down and then twisting them 90° into place.

19
 Converting Porsche 928 Interior Lighting to LEDs

Marking the Bulb Polarities on the PC Board

At some point, you should mark the polarities of each bulb position on the PC board as shown in Figure 21.

Testing the B8.4d Lamps after Installation

Once you have installed the B8.4d LED bulbs, but before you reinstall the PC board into the rest of the
instrument cluster assembly, it is prudent to test the bulbs. You can perform this test “in circuit”.

You should apply 12 V from a bench power supply (or even 9 V from a 9 V rectangular battery) to the traces near
each bulb as shown in Figure 7.

Figure 7: Testing B8.4d LED lamp "in-circuit"

It is important that:

 you observe the correct polarity as you have marked on each bulb and as shown in Figure 21;

 you apply the test current to the PC board traces near the contacts, not the LED bulb contacts! If you
were to apply the test current to the LED bulb contacts, you’re missing a key part of the test: to assure
that the LED bulb contact is actually electrically connected to the PC board trace.

Note that ordinarily, it would not be wise to apply power to a PC board in this fashion. It is safe in this
particular case because this PC board (when removed from the rest of the instrument cluster assembly)
is nothing more than a collection of electrical connections from the various connectors to the various
bulb positions—there are no active electronic components at all on this board.

20
 Converting Porsche 928 Interior Lighting to LEDs

Testing the Four #168/#194-Style Backlighting Bulbs after Installation

You can test the four analog instrument backlighting bulbs after you reinstall the PC board into the rest of the
instrument cluster assembly; the metal contacts are accessible on the edges of the twist-lock knob. Applying
12 V to one of the four twist-lock bulb bases will illuminate and test all four of them. Remember to observe the
correct polarity on the bulb.

If the bulb in the base to which you are applying current lights but the other three do not, then that base to
which you are applying current is probably not making a proper connection to the PC board (or all three of the
other bulb bases are not making a proper contact, but that is much less likely). If any of the bulbs fails to light,
you might also have incorrect polarity on those bulbs.

Anticipating and Preparing for Bulb Failures

It is quite possible that you will discover one or more failed bulbs. The sooner this discovery is made—ideally,
before you reinstall the instrument cluster into your car—the better.

To reduce the impact of failed bulbs:

 Keep some spare bulbs on hand. This is especially true for the SMD-LED-based bulbs (of the
recommended bulbs that go into the instrument cluster, the B8.4D-xHP bulbs and the WLED-WHP5
bulbs are SMD-LED-based). This will at least avoid delays in obtaining replacement parts should they
become necessary.

 Remember to mark polarities on each bulb position on the PC board. This will make it easier to replace a
failed bulb and getting its polarity correct.

To reduce the likelihood of installing a marginal bulb that is destined to fail sooner than normal, you might
consider “burning in your bulbs” for a few hours; many LED bulbs “fail fast”. If a bulb makes it through a few
hours of testing, it will likely continue to work.

Heat makes LED bulbs fail faster.

Improving Light Intensity and Reducing Unwanted Errant Light on A/T

Selector Lever Position Indicators
A little bit of further disassembly of the instrument cluster is required for this step.

Be careful when separating the last few pieces of the instrument cluster; if the pieces separate in an
uncontrolled fashion, you might damage the fragile needles on the gauges.

Separate the front and center parts of the instrument cluster with the cluster face down on a soft cloth.

You will need to, one at a time, depress the center of one of the five tabs shown in Figure 8 and Figure 9 (three
on top of the cluster, two on the bottom) while simultaneously inserting a flat-tip screwdriver into the closest
end slot shown in Figure 10 and pry the white center part of the assembly away from the front part underneath.
You’ll need to start on one of the ends and work your way around. Until you release all five tabs, you should only

21
 Converting Porsche 928 Interior Lighting to LEDs

pry the parts apart a little bit. Once all five tabs have released, you can pry at both ends simultaneously or just
go back and forth from end to end a few times.

(Figure 8 and Figure 9 show the back of the cluster still attached; yours is probably removed at this point.)

Figure 8: Three front-part-to-center-part-of-cluster latching fastening tabs on the top of the cluster

Figure 9: Two front-part-to-center-part-of-cluster latching fastening tabs on the bottom of the cluster

22
 Converting Porsche 928 Interior Lighting to LEDs

Figure 10: Slot to use for prying the front part from the center part of the cluster

The separated parts will then look like this:

Figure 11: Front part of instrument cluster (be careful with this: it is fragile and will further separate into two pieces very easily!)

23
 Converting Porsche 928 Interior Lighting to LEDs

Figure 12: Center part of instrument cluster

The A/T selector lever position indicator bulbs are enclosed in a molded plastic piece that has likely become
discolored with age and the heat of the original incandescent lamps. You might get slightly improved light
intensity from the replacement LED bulbs if you cover at least some of the discolored surfaces with white or
silver metallic tape as shown in Figure 13 and Figure 14.

Again, be very careful when working with this front part of the instrument cluster; it can still separate into two
pieces very easily, and if it does when you’re not expecting it, you can easily damage the fragile analog gauge
needles!

Figure 13: A/T selector lever position indicator bulb housings Figure 14: A/T selector lever position indicator bulb housings
before modification after white tape added to improve reflectivity
You can also add some black electrical tape as shown in Figure 16 and Figure 17 to mask some areas around the
A/T selector lever position indicator bulb housings to help prevent light bleeding through from the very intense
analog gauge backlighting.

24
 Converting Porsche 928 Interior Lighting to LEDs

Figure 15: Black tape added to help prevent analog gauge Figure 16: Black tape added to help prevent analog gauge
backlighting from bleeding into A/T selector lever position backlighting from bleeding into A/T selector lever position
indicators indicators

Cleaning the Front of the Instrument Cluster as Needed

If there is any cleaning you want to do to the front side of the cluster (analog gauges, etc.) or for any other
reason, you want to access that part of the cluster, you can easily further disassemble the front part of the
instrument cluster (the part shown in Figure 11).

Assuming the front part is still safely placed on a soft cloth face down, just carefully lift up at both ends, grasping
at the ivory-colored plastic (the bulb housings for various indicator/warning lights). The whole piece consisting
of analog gauges and all the ivory-colored parts should easily lift off of the clear plastic window. Flip this part
over (absolutely do not just set it down face down anywhere!) and you’ll see the front part of the analog
gauges, as shown in Figure 17.

At this point, you can perform any maintenance on the exposed parts.

25
 Converting Porsche 928 Interior Lighting to LEDs

Figure 17: Analog gauges, freed from their housing

Adding Resistor in Parallel to Air Bag LED Lamp

Due to a small amount of electrical current being present even when the Air Bag warning indicator is “off”, it is
necessary to add a 390 Ω, ½ W loading resistor in parallel with the air bag LED lamp. If you do not do this, that
warning indicator will stay dimly lit even when it should be off.

The resistor can be added at the location shown in Figure 18, and wired to the back of the connector shown in
Figure 19.

26
 Converting Porsche 928 Interior Lighting to LEDs

Figure 18: Added 390 Ω, ½ W loading resistor in parallel to air bag LED lamp

Figure 19: Connections for air bag LED loading resistor; solder wires as shown

27
 Converting Porsche 928 Interior Lighting to LEDs

Instrument Cluster Reinstallation

Generally, instrument cluster reinstallation is the reverse of removal.

A few tips:

 When refastening the five socket head cap screws (see Figure 2), you may find it difficult to get the three
longer ones to thread into its corresponding nut. It may require some jiggling of the whole pod.

 Do not fully tighten all five socket head cap screws until all five are at partially threaded; this will allow
pod movement, allowing remaining screws to threaded. You may find that a long screwdriver with a tip
smaller than the nut for each screw can
be used to position screw hole properly
over the nut.

 The middle (and long) socket head cap

screw on the side of the cluster held by
three screws, if pushed up very hard
without engaging the nut, can push the
nut out of its holder. You might want to
locate the nut so you’re prepared to
prevent this; it is possible to get a finger
on top of it to prevent it from being
pushed upward. Alternatively, you can

just be very gentle when threading that Figure 20: Taping the spacers, bushings, and washer
screw.

 As shown in Figure 21, use some tape to attach the aluminum spacers, plastic/rubber bushings, and the
washer for the left end of the instrument cluster. This holds those components together, reducing the
likelihood that you will have problems with this part of reassembly.

28
 Converting Porsche 928 Interior Lighting to LEDs

Figure 21: Back and front of PC board after LED replacement; black marks Indicate LED cathode (low/ground) side

29
 Converting Porsche 928 Interior Lighting to LEDs

Additional Labeling on PC Board

In Figure 21, you’ll note some additional labels and markings (beyond the polarity markings at each bulb
position, already recommended in an earlier section of this document) that have been added to the PC board:

 White-on-clear label “Remove four large brown lamps before removing/installing PC board”: this label
provides a reminder that may be helpful during any future maintenance involving PC board removal and
reinstallation.

 White-on-clear label “Air bag LED loading resistor”: this label explains the purpose of the added resistor.

 White-on-clear label “Converted to use LEDs…”: this label

provides a record of the significant modification to LEDs
that has been performed on the PC board.
Instrument Cluster Anomalies
 Black “X” marks over the two lower-most holes (that, other The following minor imperfections were
noted with the instrument cluster after
than the white circle around them, look like the other
performing the LED upgrades as
screw holes) to clearly indicate that those holes are not described in this document:
used when refastening the PC board to the white plastic
part of the instrument cluster assembly.  The air bag warning light illuminates
very briefly (probably just a few
milliseconds; barely noticeable) at
regular intervals approximately every
three seconds when the system is
operating normally.

 After shutting off the ignition, the

park brake warning light (if the park
brake is applied) and the ABS warning
light are illuminated very dimly as
long as the information system
display remains backlit.

Further tweaks (like loading resistors in

parallel with the corresponding LEDs)
might eliminate these anomalies; I
didn’t believe that it was worth the
additional circuitry.

30
 Converting Porsche 928 Interior Lighting to LEDs

Pod Switches
Pod Switch Lamp Summary
Large Cylindrical Switch Knob Backlighting (5 Switches)
Bulb Socket W2x4.6d
Original Bulb Type W1.2W-12V with T1-1/2 glass (4.8 mm diameter,
18 mm long wedge base; slightly smaller than #74)
Recommended LED Replacement Bulb Type  for light switch knob and fog light switch knob:
Autolumination “#74 Super High Power 1 Watt
Super-Charged LED Bulb”, green
 for zero button: Autolumination “#74 Super High
Power 1 Watt Super-Charged LED Bulb”, white
 for rear window defogger switch knob:
Autolumination “#74 Super High Power 1 Watt
Super-Charged LED Bulb”, amber
 for emergency flasher switch knob:
Autolumination “#74 Super High Power 1 Watt
Super-Charged LED Bulb”, red
Notes  Wrap thin layer of tape around base as
necessary to make snug fit between bulb and
socket, preventing bulb from popping out of
socket.

Intensive Cleaning Switch Backlighting

Bulb Socket none; through-hole
Original Bulb Type 3 mm discrete LED
Recommended LED Replacement Bulb Type Super Bright LEDs RL3-W6045
Notes Only necessary if you want to change an existing
yellow LED to white.

Normal Pod Switch Backlighting Behavior

The normal behavior of the pod switch knob backlighting (in case you never noticed it, or have burned out bulbs,
etc.) is:

 The lights switch knob is always fully lit; this is probably so it can be found in the dark, regardless of
whether or not the lights are on.

 For the fog lights switch, rear window defogger switch, and emergency flasher switch, the knob is:

o unlit if the lights are off and the switch’s corresponding function is inactive (switched off);

31
 Converting Porsche 928 Interior Lighting to LEDs

o dimly lit (with dimming level set by the instrument illumination control) if the lights are on and
the switch’s corresponding function is inactive (switched off); and

o fully lit if the switch’s corresponding function is active (switched on).

 The zero button knob is unlit if the lights are off and lit (with dimming level set by the instrument
illumination control) if the lights are on

Tools for Use Working With the Large Cylindrical Pod

Switches
An IC removal tool (available from many electronic parts and tools vendors, e.g., Jameco 16838) makes
it very easy to remove the large cylindrical pod switches from the pod.

A small piece of ¼ inch clear vinyl tubing makes a good tool for removing the original pod switch bulbs (it
fits over the end of the bulb and makes it much easier to get a grip on the bulb).

Large Cylindrical Pod Switch Removal

While you do not need to remove the pod switches to replace the
bulbs, you will need to remove three of them (the fog light switch,
the rear window defogger switch, and the emergency flasher Removing Porsche 928
switch) to get to the socket wiring to install the current-limiting Instrument Pod Switches: The
resistors to make the LED bulbs dimmer when the switch is “off”. Video
The YouTube® video “Removing Porsche
The knobs are friction-fit and just pull off the switches (and are just 928 instrument pod switches”
pushed back on to reinstall). demonstrates the use of the IC extractor
tool to remove a pod switch.
To remove a pod switch from the pod, use the IC removal tool (or
equivalent) to grab the pod switch by the “ear tabs”, compress the
ear tabs, and pull. The photos below show the how the IC extractor tool is used to grab a pod switch (which
normally would still be in the pod).

32
 Converting Porsche 928 Interior Lighting to LEDs

Replacing the Original Incandescent Bulbs with LED Bulbs

Bulb replacement is trivial; just:

1. Remove the original incandescent bulb (using a piece of vinyl tubing to get a grip on the bulb if
necessary);

2. Wrap a thin piece of tape around the base of the recommended replacement LED bulb and push it into
place. Adjust the amount of tape as necessary to get a snug fit. Test that the bulb stays in place by
reinstalling the switch’s knob. For some of the switches, you’ll note that when reinstalling the knob, the
center portion of the switch that holds the bulb will snap outward and may eject the bulb; if this
happens, you’ll need to add a little more tape to the base of the bulb.

Repeat the procedure for each of the five large cylindrical pod switches:

 Light switch and fog light switch (green bulbs);

 Zero button (white bulb);

 Rear window defogger switch (amber bulb);

 Emergency flasher switch (red bulb).

When fully lit, the switch backlighting looks like this:

33
 Converting Porsche 928 Interior Lighting to LEDs

Adding Resistors to Set Maximum “Dim” Level

To preserve the original behavior of the backlighting, three of the large cylindrical pod switches (fog lights, rear
window defogger, and emergency flasher) need to have resistors added so they will dim appropriately when the
switch is off. Likewise, you need to add a resistor for the zero button (even though it doesn’t have a separate
on/off brightness); otherwise it is too bright.

This modification is necessary because of the reduced power demands of the LED bulbs (more resistance is
needed to dim the LED bulbs than was originally used to dim the incandescent bulbs).

The recommended resistor values (assuming the recommended LED bulbs have been used) are:

 1.8 kΩ, ½ W (or ¼ W) carbon film resistor for fog lights switch, emergency flasher switch, and zero
button;

 1 kΩ, ½ W (or ¼ W) carbon film resistor for the rear defogger switch.

In each case, you will need to cut the BK/BL (black wire with blue stripe) leading to the switch’s socket and
solder or crimp in the resistor. Cover the solder joints and resistor with heat shrinkable tubing (remember to
thread the heat shrinkable tubing onto the wire before soldering the resistor in!)

34
 Converting Porsche 928 Interior Lighting to LEDs

Intensive Windshield Cleaning Switch

The intensive windshield switch may have a yellow LED backlight. If you wish to replace this with a white LED,
you’ll need to remove the entire switch assembly. Then very carefully (to avoid breaking the brittle plastic), use
one or two very small screwdrivers to pry the little switch/LED/resistor module out of the black housing. Watch
out for the small red plastic cylinder; you need to make sure it’s reinstalled as shown or else pressing the black
plastic switch cover won’t activate the small PC-board-mounted switch underneath.

If you wish to bench test the LED backlighting, just apply 12 V to the terminals (the top two in the photo) as
shown in Figure 22.

Figure 22: Terminals for testing intensive windshield washer switch backlighting

35
 Converting Porsche 928 Interior Lighting to LEDs

To replace the LED, desolder the old one (a solder sucker and/or solder wick are helpful) and then solder in the
new one, making sure to orient it the same way as the original one (especially with respect to the polarity).
Solder quickly and/or use a heat sink as shown to reduce the likelihood of damaging the heat-sensitive LED.

Figure 23: Soldering the replacement LED to the intensive windshield washer switch module (cathode on right)

Bend the leads of the LED so the beam fires slightly inward as shown.

36
 Converting Porsche 928 Interior Lighting to LEDs

Center Console Switches and Instrumentation

Automatic Climate Control
Central Door Locking Button
Clock
Cigarette Lighter / Ashtray

Courtesy Lighting
Footwell Lights in Lower Door Panels
Light in Headlining Near Front Visors
Light in Headlining Near Rear Visors
Luggage Compartment Light
Glove Box Light
Central Electric Panel Area Light

37
 Converting Porsche 928 Interior Lighting to LEDs

Restoring Dimming Functionality

The factory 928 instrument illumination control (a simple rheostat that adjusts current supplied to the
instrument backlighting circuit) will not function with LED lights; it does no harm, but it provides little if any
noticeable dimming.

After being unable to find an off-the-shelf solution to this problem, I developed a microcontroller- and PWM-
based dimmer module that restores the dimming functionality using the existing dimmer control (rheostat)
already present.

The solution wound up being effective enough that I decided to develop it into a nearly commercial-grade
product, although its hand assembly
will greatly limit the number of these I
can produce.

For more information about this device,

see Protizmo AILD-1 Automotive
Instrumentation Lighting Dimmer.

38
 Converting Porsche 928 Interior Lighting to LEDs

Part Summary
Order Extras!
Save yourself the trouble of having to place additional orders for replacement LED bulbs in case any fail or don’t
match in intensity or color with others. This is especially recommended for the information display backlighting
LED bulbs and the analog gauge backlighting bulbs, which seem most prone to failure and matching issues.

Instrument Cluster
For A/T clusters with the P/R/N/D/3/2 indicator bulbs, the below table assumes you are using all white
bulbs. If you prefer to use the alternative color scheme shown in Figure 7, subtract five white B8.4D-
WHP bulbs and add one red B8.4D-RHP bulb, one amber B8.4D-AHP bulb, and three B8.4D-GHP bulbs.

Qty Part Used For Available From

11 B8.4d LED bulb,  brake fluid warning light Super Bright LEDs B8.4D-R
red  park brake warning light
 air bag warning light
 oil pressure warning light
 safety belt warning light
 catalytic converter warning light
(optional)
 tire pressure warning light
 voltmeter warning light
 check engine light (optional)
 stop lamp warning light
 coolant temperature warning light
4 B8.4d LED bulb,  trailer turn signal indicator light Super Bright LEDs B8.4D-G
green  turn signal indicator light
 parking light indicator
 PSD warning light
1 B8.4d LED bulb,  high beam indicator light Super Bright LEDs B8.4D-B
blue
2 B8.4d LED bulb,  fuel level warning light Super Bright LEDs B8.4D-A
amber  ABS warning light
6 B8.4d LED bulb,  selector lever position indicator Super Bright LEDs B8.4D-WHP
white, high- (automatic transmission only)
intensity
4 B8.4d LED bulb,  information display backlighting Super Bright LEDs B8.4D-AHP
amber, high- (normal display)
intensity
4 B8.4d LED bulb,  information display backlighting Super Bright LEDs B8.4D-RHP
red, high-intensity (fault display)

39
 Converting Porsche 928 Interior Lighting to LEDs

Qty Part Used For Available From

4 #168/#194-style  analog gauge backlighting Super Bright LEDs WLED-WHP5
LED bulb with
W2.1x9.5d base,
white
1 330 Ω, ½ W  loading resistor for air bag warning numerous sources (e.g., Radio Shack)
carbon film light
resistor

Pod Switches
There are many #74 style bulbs available from various sources; the ones recommended below were
chosen because (of various ones tested), they were appropriately bright, cool running, and had bases
that didn’t need to be filed to fit into the sockets in the pod switches (quite the contrary—it might take a
little tape around the bases to keep them from popping out).

Qty Part Used For Available From

2 #74-style LED  light switch backlighting Autolumination “#74 Super High Power
bulb, green  fog light switch backlighting 1 Watt Super-Charged LED Bulb”, green
1 #74-style LED  zero button backlighting Autolumination “#74 Super High Power
bulb, white 1 Watt Super-Charged LED Bulb”, super
white
1 #74-style LED  rear window defogger switch Autolumination “#74 Super High Power
bulb, amber backlighting 1 Watt Super-Charged LED Bulb”, amber
1 #74-style LED  emergency flasher switch Autolumination “#74 Super High Power
bulb, red backlighting 1 Watt Super-Charged LED Bulb”, red
1 3 mm, 45°  intensive washer switch Super Bright LEDs RL3-W6045
discrete LED, backlighting (optional: if was
white originally yellow LED and you want
to replace it with white)
4 1.8 kΩ, ½ W (or  current limiter to dim fog light numerous sources (e.g., Radio Shack)
¼ W) carbon film switch backlighting when switched
resistor “off”
 current limiter to dim zero switch
backlighting at all times (it’s too
bright otherwise)
 current limiter to dim emergency
flasher switch backlighting when
switched “off”
1 1 kΩ, ½ W (or  current limiter to dim rear window numerous sources (e.g., Radio Shack)
¼ W) carbon film defogger switch backlighting when
resistor heating element is switched off

40
 Converting Porsche 928 Interior Lighting to LEDs

Center Console Switches and Instrumentation

Qty Part Used For Available From
1 5 mm, 15°  climate control fan speed switch Super Bright LEDs RL5-W18015
discrete LED, backlighting
white
1 1 kΩ, ½ W carbon  current limiting resistor for climate numerous sources (e.g., Radio Shack)
film resistor control fan speed switch
backlighting LED
1 1N4148 or 1N914  reverse voltage protection for numerous sources (e.g., Radio Shack)
diode climate control fan speed switch
backlighting LED (optional)
1 #74-style top-and-  climate control head (including Autolumination “#74 Matrix II, 5 LED 5x
side firing 5-SMD sliders) backlighting brighter”, super white
LED bulb
1 #74-style LED  rectangular A/C button backlighting Super Bright LEDs 74-WHP
bulb, high
intensity
1 5 mm, 60°  central door locking button Super Bright LEDs RL5-RD1560
discrete LED, red backlighting
1 1.8 kΩ, ½ W (or  current limiting resistor for central numerous sources (e.g., Radio Shack)
¼ W) carbon film door locking button backlighting
resistor when indicating “unlocked” (dim)
1 680 Ω, ½ W (or  current limiting resistor for central numerous sources (e.g., Radio Shack)
¼ W) carbon film door locking button backlighting
resistor when indicating “locked” (bright)
1 B8.5d LED bulb,  clock backlighting Super Bright LEDs B8.5D-WHP
white, high-
intensity
1 BA7s LED bulb,  lighter backlighting Super Bright LEDs BA7S-W
white

Courtesy Lighting
Qty Part Used For Available From
3 42 mm festoon-  footwell light in left door panel Super Bright LEDs 4210-CWHP6
style LED bulb,  footwell light in right door panel
front-firing, wide,  overhead light in headlining near
white front visors
3 42 mm festoon-  overhead light in headlining near Super Bright LEDs 4210-CWHP3
style LED bulb, rear visors
front-firing,  luggage compartment/hatch light
narrow, white  central electric panel area light
1 30 mm festoon-  glove box light Super Bright LEDs 3022-W9
style LED bulb,
front-firing, white

41
 Converting Porsche 928 Interior Lighting to LEDs

[TBA: seat position memory switch backlighting]

42